Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

DAC39RFS10 Datasheet(PDF) 71 Page - Texas Instruments

Part # DAC39RFS10
Description  DDS39RF12 and DDS39RFS12, 12GSPS to 24GSPS, Dual and Single Channel, Multi- Nyquist Direct Digital Synthesizer (DDS)
PDF  177 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI2 [Texas Instruments]
Direct Link  https://www.ti.com
Logo TI2 - Texas Instruments

DAC39RFS10 Datasheet(HTML) 71 Page - Texas Instruments

Back Button DAC39RFS10 Datasheet HTML 67Page - Texas Instruments DAC39RFS10 Datasheet HTML 68Page - Texas Instruments DAC39RFS10 Datasheet HTML 69Page - Texas Instruments DAC39RFS10 Datasheet HTML 70Page - Texas Instruments DAC39RFS10 Datasheet HTML 71Page - Texas Instruments DAC39RFS10 Datasheet HTML 72Page - Texas Instruments DAC39RFS10 Datasheet HTML 73Page - Texas Instruments DAC39RFS10 Datasheet HTML 74Page - Texas Instruments DAC39RFS10 Datasheet HTML 75Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 71 / 177 page
background image
TX LMFC/LEMC
RX LMFC/LEMC
TX 1 Data
Propagation
t
TX
t
PCB
t
RX-DESER
Time
TX 2 Data
Propagation
t
TX
t
PCB
Invalid Region
of LMFC/LEMC
Valid Region of
LMFC/LEMC
Nominal Link Delay
(Arrival at Elastic Buffer)
Link Delay
Variation
Choose LMFC/LEMC
edge as release point
(RBD = 0)
Release point
margin
t
RX-DESER
Figure 7-54. LMFC Valid Region Definition for Elastic Buffer Release Point Selection
The TX and RX LMFC do not necessarily need to be phase aligned, but knowledge of their phase is important
for proper elastic buffer release point selection. Also, the elastic buffer release point occurs within every LMFC
cycle, but the buffers only release when all lanes have arrived. Therefore, the total link delay can exceed a
single LMFC period; see JESD204B multi-device synchronization: Breaking down the requirements for more
information.
7.3.7.8.1 Programming RBD
The range of values for RBD depends on the phase delta between the Rx and Tx LMFC/LEMC, as well as link
latencies in the Tx, channel, and Rx. Therefore, do not provide a pre-determined RBD value that is appropriate
for all systems. The LANE_ARR registers are provided to help the user measure lane arrival times and select an
appropriate RBD value for the system. For deterministic latency, the RBD value can be selected during system
prototyping and stored in system firmware. Calculating RBD each time the system is turned on can result in
non-deterministic latency.
The arrival times are reported in units of quad-bytes and are measured with respect to a modulo-64 reference
counter that increments for each quad-byte received (per lane). The reference counter is aligned (reset) by
SYSREF.
Since the lane arrival times are modulo-values, it is important to use arithmetic that accounts for the modulus
(the latest arriving lane might actually have a smaller LANE_ARR value than the earliest arriving lane). Figure
7-55 and Figure 7-56 depict the RBD calculation graphically to emphasize this. The lane arrival times are
mapped onto a circle with a circumference of 64 quad-bytes which corresponds to the modulo-64 counter used
to measure lane arrival times.
The earliest usable RBD value is equal to the latest LANE_ARR value plus 1 (modulo 64). The latest usable
RBD value is equal to the earliest LANE_ARR value plus the buffer depth (modulo 64) (the buffer depth is 16
quad-octets, except when K x F = 32, then the buffer depth is reduced to 8 quad-octets). Note that the latest,
usable RBD value causes the earliest arriving lane to overwrite buffer data on the same clock cycle that the data
is being read out (this is acceptable and does not cause overflow).
Choosing an RBD value in the middle of the usable range maximizes the skew tolerance; however, the user can
choose a value closer to the latest arriving lane if lower latency is desired.
www.ti.com
DDS39RF12, DDS39RFS12
SBASB21 – SEPTEMBER 2024
Copyright © 2025 Texas Instruments Incorporated
Submit Document Feedback
71
Product Folder Links: DDS39RF12 DDS39RFS12



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com