| Electronic Components Datasheet Search |
|
BATT-TPLCABLE50 Datasheet(PDF) 6 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
BATT-TPLCABLE50 Datasheet(HTML) 6 Page - NXP Semiconductors |
|
6 / 16 page ![]() NXP Semiconductors UM11734 Hardware user manual for FRDM665SPIEVB 4.3 Block diagram aaa-044811 REQUEST SPI VDDIO CFG0, CFG1 ID0_STB_OD, ID1, ID2, ID3 DIP switch 3V3LDO J13 J8 SW1 J1 D8 RESPONSE SPI TPL PORT 0 LDO MC33665A POWER MANAGEMENT GPIO, CONFIG AND STATUS PINS TPL PORT 1 TPL PORT 2 TPL PORT 3 reset switch VBAT KL30/ 12 V/T30 VDD5V VREG VDDC/VDDD VDD5V VREG VREG EXT5V 5V_S32K VIO_S32K external interface for GPIO and status signals Figure 1. FRDM665SPIEVB block diagram 4.4 Board description The FRDM665SPIEVB allows the user to prototype and test all functions of the MC33665A gateway router. It can be stacked directly on the S32K344EVB. Different modes of SPI communication can be established with MC33665A from K1 to K6 connectors. The FRDM665SPIEVB can be supplied with 12 V at J6 connector or it can be powered directly from S32K344EVB or EXT5V at J11. VDDC and VDDD can be selected by bridging one of the positons in jumper J8 (Table 7) to select the 5 V. Bridging options jumper at J13 (Table 8) makes it possible to select the VIO voltage of 3.3 V or 5 V or VIO of S32K344EVB. S32K344EVB can be supplied with USB connection when connected to a PC. SPI interface to external controller boards can be done with J7 for REQ SPI and J16 for RSP SPI. Ensure the VIO of external controller board is the same as the VIO selected with jumper J13. Single SPI or dual SPI modes can be selected by using jumpers at J14. Populating all jumpers at J14 enables single SPI mode and depopulates jumpers at J14 for dual SPI mode. SW2 DIP switch can be used to select the CFG and ID configuration for MC33665A. BCC devices can be connected to daisy chain ports 0 to 3 via connectors J5, J12, J17, and J18. Connector J1 gives the option to access the GPIO and I2C-bus pins of MC33665A. Contact the NXP engineering team for using TPL_AUTOWAKE function in FRDM665SPIEVB. UM11734 All information provided in this document is subject to legal disclaimers. © 2022 NXP B.V. All rights reserved. User manual Rev. 2 — 25 August 2022 6 / 16 |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |