AT80C51RA2-RLSIV datasheet(60/86 Pages) ATMEL

60 / 86 page

4188F–8051–01/08

AT/TS8xC51Rx2

11.4

DC Parameters for Low Voltage

TA = 0°C to +70°C; VSS = 0 V; VCC = 2.7 V to 5.5 V ± 10%; F = 0 to 30 MHz.

TA = -40°C to +85°C; VSS = 0 V; VCC = 2.7 V to 5.5 V ± 10%; F = 0 to 30 MHz.

Notes: 1. ICC under reset is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns (see Figure 11-5.), VIL

= VSS + 0.5 V,

VIH = VCC - 0.5V; XTAL2 N.C.; EA = RST = Port 0 = VCC. ICC would be slightly higher if a crystal oscillator used..

2. Idle ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns, VIL = VSS + 0.5 V, VIH = VCC -

0.5 V; XTAL2 N.C; Port 0 = VCC; EA = RST = VSS (see Figure 11-3.).

3. Power-down ICC is measured with all output pins disconnected; EA = VSS, PORT 0 = VCC; XTAL2 NC.; RST = VSS (see Fig-

ure 11-4.).

Table 11-2.

DC Parameters for Low Voltage

Symbol

Parameter

Min

Typ

Max

Unit

Test Conditions

VIL

Input Low Voltage

-0.5

0.2 VCC - 0.1

VIH

Input High Voltage except XTAL1, RST

0.2 VCC + 0.9

VCC + 0.5

VIH1

Input High Voltage, XTAL1, RST

0.7 VCC

VCC + 0.5

VOL

Output Low Voltage, ports 1, 2, 3, 4, 5 (6)

0.45

IOL = 0.8 mA(4)

VOL1

Output Low Voltage, port 0, ALE, PSEN (6)

0.45

IOL = 1.6 mA(4)

VOH

Output High Voltage, ports 1, 2, 3, 4, 5

0.9 VCC

IOH = -10 µA

VOH1

Output High Voltage, port 0, ALE, PSEN

0.9 VCC

IOH = -40 µA

IIL

Logical 0 Input Current ports 1, 2, 3, 4, 5

-50

µA

Vin = 0.45 V

ILI

Input Leakage Current

±10

µA

0.45 V < Vin < VCC

ITL

Logical 1 to 0 Transition Current, ports 1, 2, 3, 4,

-650

µA

Vin = 2.0 V

RRST

RST Pulldown Resistor

90 (5)

200

kΩ

CIO

Capacitance of I/O Buffer

Fc = 1 MHz

TA = 25°C

IPD

Power-down Current

20 (5)

10 (5)

µA

VCC = 2.0 V to 5.5 V(3)

VCC = 2.0 V to 3.3 V(3)

IPD

Power-down Current (Only for TS87C51RD2

S287-xxx Very Low power)

2 (5)

µA

2.0 V < VCC < 3.6 V(3)

ICC

under

RESET

Power Supply Current Maximum values, X1

mode: (7)

1 + 0.2 Freq

(MHz)

@12MHz 3.4

@16MHz 4.2

VCC = 3.3 V(1)

ICC

operating

Power Supply Current Maximum values, X1

mode: (7)

1 + 0.3 Freq

(MHz)

@12MHz 4.6

@16MHz 5.8

VCC = 3.3 V(8)

ICC

idle

Power Supply Current Maximum values, X1

mode: (7)

0.15 Freq

(MHz) + 0.2

@12MHz 2

@16MHz 2.6

VCC = 3.3 V(2)

AT80C51RA2-RLSIV Datasheet(PDF) 60 Page - ATMEL Corporation

AT80C51RA2-RLSIV Datasheet(HTML) 60 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

Datasheet Download

Link URL