PIC18F44J10-ISLASHML datasheet(103/368 Pages) MICROCHIP

103 / 368 page

DS39682E-page 101

PIC18F45J10 FAMILY

10.3

PORTB, TRISB and LATB

Registers

PORTB is an 8-bit wide, bidirectional port. The corre-

sponding Data Direction register is TRISB. Setting a

TRISB bit (= 1) will make the corresponding PORTB

pin an input (i.e., put the corresponding output driver in

a high-impedance mode). Clearing a TRISB bit (= 0)

will make the corresponding PORTB pin an output (i.e.,

put the contents of the output latch on the selected pin).

The Data Latch register (LATB) is also memory

mapped. Read-modify-write operations on the LATB

PORTB.

EXAMPLE 10-3:

INITIALIZING PORTB

Each of the PORTB pins has a weak internal pull-up. A

single control bit can turn on all the pull-ups. This is

performed by clearing bit, RBPU (INTCON2<7>). The

weak pull-up is automatically turned off when the port

pin is configured as an output. The pull-ups are

disabled on a Power-on Reset.

Four of the PORTB pins (RB<7:4>) have an interrupt-

on-change feature. Only pins configured as inputs can

cause this interrupt to occur (i.e., any RB<7:4> pin

configured as an output is excluded from the interrupt-

on-change comparison). The input pins (of RB<7:4>)

are compared with the old value latched on the last

read of PORTB. The “mismatch” outputs of RB<7:4>

are ORed together to generate the RB Port Change

Interrupt with Flag bit, RBIF (INTCON<0>).

This interrupt can wake the device from Sleep mode or

any of the Idle modes. The user, in the Interrupt Service

Routine, can clear the interrupt in the following manner:

a) Any read or write of PORTB (except with the

MOVFF (ANY), PORTB

instruction).

b) Clear flag bit, RBIF.

A mismatch condition will continue to set flag bit, RBIF.

Reading PORTB will end the mismatch condition and

allow flag bit, RBIF, to be cleared.

The interrupt-on-change feature is recommended for

wake-up on key depression operation and operations

where PORTB is only used for the interrupt-on-change

feature. Polling of PORTB is not recommended while

using the interrupt-on-change feature.

RB3 can be configured by the Configuration bit,

CCP2MX, as the alternate peripheral pin for the CCP2

module (CCP2MX = 0).

The RB5 pin is multiplexed with the Timer0 module

clock input and one of the comparator outputs to

become the RB5/KBI1/T0CKI/C1OUT pin.

Note:

On a Power-on Reset, RB<4:0> are

configured as analog inputs by default and

read as ‘0’; RB<7:5> are configured as

digital inputs.

CLRF

PORTB

; Initialize PORTB by

; clearing output

; data latches

CLRF

LATB

; Alternate method

; to clear output

; data latches

MOVLW

0Fh

; Set RB<4:0> as

MOVWF

ADCON1

; digital I/O pins

MOVLW

0CFh

; Value used to

; initialize data

; direction

MOVWF

TRISB

; Set RB<3:0> as inputs

; RB<5:4> as outputs

; RB<7:6> as inputs

PIC18F44J10-I/ML Datasheet(PDF) 103 Page - Microchip Technology

PIC18F44J10-I/ML Datasheet(HTML) 103 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL