PIC18F23K22-ESLASHML datasheet(249/496 Pages) MICROCHIP

249 / 496 page

 2010 Microchip Technology Inc.

Preliminary

DS41412C-page 249

PIC18(L)F2X/4XK22

15.6.13.1

Bus Collision During a Start

Condition

During a Start condition, a bus collision occurs if:

SDAx or SCLx are sampled low at the beginning

of the Start condition (Figure 15-32).

SCLx is sampled low before SDAx is asserted

low (Figure 15-33).

During a Start condition, both the SDAx and the SCLx

pins are monitored.

If the SDAx pin is already low, or the SCLx pin is

already low, then all of the following occur:

• the Start condition is aborted,

• the BCLxIF flag is set and

• the MSSPx module is reset to its Idle state

(Figure 15-32).

The Start condition begins with the SDAx and SCLx

pins deasserted. When the SDAx pin is sampled high,

the Baud Rate Generator is loaded and counts down. If

the SCLx pin is sampled low while SDAx is high, a bus

collision occurs because it is assumed that another

master is attempting to drive a data ‘1’ during the Start

condition.

If the SDAx pin is sampled low during this count, the

BRG is reset and the SDAx line is asserted early

(Figure 15-34). If, however, a ‘1’ is sampled on the

SDAx pin, the SDAx pin is asserted low at the end of

the BRG count. The Baud Rate Generator is then

reloaded and counts down to zero; if the SCLx pin is

sampled as ‘0’ during this time, a bus collision does not

occur. At the end of the BRG count, the SCLx pin is

asserted low.

FIGURE 15-33:

BUS COLLISION DURING START CONDITION (SDAx ONLY)

Note:

The reason that bus collision is not a factor

during a Start condition is that no two bus

masters can assert a Start condition at the

exact same time. Therefore, one master

will always assert SDAx before the other.

This condition does not cause a bus colli-

sion because the two masters must be

allowed to arbitrate the first address fol-

lowing the Start condition. If the address is

the same, arbitration must be allowed to

continue into the data portion, Repeated

Start or Stop conditions.

SDAx

SCLx

SEN

SDAx sampled low before

SDAx goes low before the SEN bit is set.

S bit and SSPxIF set because

SSPx module reset into Idle state.

SEN cleared automatically because of bus collision.

S bit and SSPxIF set because

Set SEN, enable Start

condition if SDAx = 1, SCLx = 1

SDAx = 0, SCLx = 1.

BCLxIF

SSPxIF

SDAx = 0, SCLx = 1.

SSPxIF and BCLxIF are

cleared by software

SSPxIF and BCLxIF are

cleared by software

Set BCLxIF,

Start condition. Set BCLxIF.

PIC18F23K22-E/ML Datasheet(PDF) 249 Page - Microchip Technology

PIC18F23K22-E/ML Datasheet(HTML) 249 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL