PIC18F23K22-ESLASHML datasheet(178/496 Pages) MICROCHIP

178 / 496 page

PIC18(L)F2X/4XK22

DS41412C-page 178

Preliminary

 2010 Microchip Technology Inc.

14.1

Capture Mode

The Capture mode function described in this section is

identical for all CCP and ECCP modules available on

this device family.

Capture mode makes use of the 16-bit Timer

resources, Timer1, Timer3 and Timer5. The timer

resources for each CCP capture function are

independent and are selected using the CCPTMRS0

and CCPTMRS1 registers. When an event occurs on

the CCPx pin, the 16-bit CCPRxH:CCPRxL register

pair captures and stores the 16-bit value of the

TMRxH:TMRxL register pair, respectively. An event is

defined as one of the following and is configured by the

CCPxM<3:0> bits of the CCPxCON register:

• Every falling edge

• Every rising edge

• Every 4th rising edge

• Every 16th rising edge

When a capture is made, the corresponding Interrupt

Request Flag bit CCPxIF of the PIR1, PIR2 or PIR4

software. If another capture occurs before the value in

the CCPRxH:CCPRxL register pair is read, the old

captured value is overwritten by the new captured

value.

Figure 14-1 shows a simplified diagram of the Capture

operation.

FIGURE 14-1:

CAPTURE MODE

OPERATION BLOCK

DIAGRAM

14.1.1

CCP PIN CONFIGURATION

In Capture mode, the CCPx pin should be configured

as an input by setting the associated TRIS control bit.

Some CCPx outputs are multiplexed on a couple of

pins.

Table 14-2

shows

the

CCP

output

multiplexing. Selection of the output pin is determined

by the CCPxMX bits in Configuration register 3H

(CONFIG3H). Refer to Register 24-4 for more details.

14.1.2

TIMER1 MODE RESOURCE

The 16-bit Timer resource must be running in Timer

mode or Synchronized Counter mode for the CCP

module to use the capture feature. In Asynchronous

Counter mode, the capture operation may not work.

See Section 12.0 “Timer1/3/5 Module with Gate

Control” for more information on configuring the 16-bit

Timers.

14.1.3

SOFTWARE INTERRUPT MODE

When the Capture mode is changed, a false capture

interrupt may be generated. The user should keep the

CCPxIE interrupt enable bit of the PIE1, PIE2 or PIE4

user should clear the CCPxIF interrupt flag bit of the

PIR1, PIR2 or PIR4 register following any change in

Operating mode.

Note:

If the CCPx pin is configured as an output,

a write to the port can cause a capture

condition.

CCPRxH

CCPRxL

TMR1/3/5H TMR1/3/5L

Set Flag bit CCPxIF

(PIR1/2/4 register)

Capture

Enable

CCPxM<3:0>

Prescaler

 1, 4, 16

and

Edge Detect

CCPx

System Clock (FOSC)

TABLE 14-2:

CCP PIN MULTIPLEXING

CCP OUTPUT

CONFIG 3H Control Bit

Bit Value

PIC18(L)F2XK22 I/O pin

PIC18(L)F4XK22 I/O pin

CCP2

CCP2MX

RB3

1(*)

RC1

CCP3

CCP3MX

0(*)

RC6

RE0

RB5

Legend: * = Default

Note:

Clocking the 16-bit Timer resource from

the system clock (FOSC) should not be

used in Capture mode. In order for

Capture mode to recognize the trigger

event on the CCPx pin, the Timer resource

must be clocked from the instruction clock

(FOSC/4) or from an external clock source.

PIC18F23K22-E/ML Datasheet(PDF) 178 Page - Microchip Technology

PIC18F23K22-E/ML Datasheet(HTML) 178 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL