PRF18BE471RB5RB datasheet(94/104 Pages) MURATA

94 / 104 page

!Caution/Notice

(2) Drying

After cleaning, promptly dry this product.

To remove the flux after soldering, observe the following

points in order to avoid deterioration of the characteristics

or any change to the external electrodes quality.

(1) Cleaning Conditions

2-propanol

Less than 5 minutes

at room temp.

Less than 2 minutes

at 40˚C max.

Less than 1 minute

20W/L Frequency

of several 10kHz

to 100kHz.

Solvent

Dipping Cleaning

Ultrasonic Cleaning

A sufficient cleaning should be applied to remove flux completely.

(1) Printing Conditions of Solder Paste

(a) Standard thickness of solder paste printing should

be from 0.10 to 0.15 mm.

(b) After soldering, the solder fillet should be a height

from 0.15 mm to the thickness of this product (see the

figure at right).

to this product. Such stress may cause cracking or

other mechanical damage. Also, it can destroy the

electrical performance of this product.

In your mounting process, observe the following points in

order to avoid deterioration of the characteristics or

destruction of this product. The mounting quality of this

product may also be affected by the mounting conditions,

shown in the points below.

This product is for reflow soldering only. Flow soldering

should not be allowed.

0.15mm

V T V E

Solder

Electrode

1. Solder and Flux

2. Cleaning Conditions and Drying

3. Soldering Conditions

(1) Solder Paste

Use solder paste Sn:Pb=63:37wt%.

For your reference, we are using

63Sn/37Pb RMA9086 90-3-M18,

manufactured by Alpha Metals Japan Ltd.

96.5Sn/3.0Ag/0.5Cu M705-GRN360-K2-V,

manufactured by Senju Metal Industry Co., LTD for any

Internal tests of this product.

(2) Flux

Use rosin type flux in soldering process.

If below flux is used, some problems might be caused

in the product characteristics and reliability.

Please do not use below flux.

0.2wt%).

(*Water-soluble flux can be defined as non rosin type

flux including wash-type flux and non-wash-type flux.)

Continued on the following page.

c Notice (Soldering and Mounting) PRF15_103R Series

R90E.pdf

Sep.24,2012

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical speciﬁcations. Therefore, please approve our product speciﬁcations or transact the approval sheet for product speciﬁcations before ordering.

PRF18BE471RB5RB Datasheet(PDF) 94 Page - Murata Manufacturing Co., Ltd.

PRF18BE471RB5RB Datasheet(HTML) 94 Page - Murata Manufacturing Co., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL