PIC17C752-08SLASHP datasheet(97/320 Pages) MICROCHIP

97 / 320 page

Preliminary

DS30264A-page 97

PIC17C75X

13.1.3

USING PULSE WIDTH MODULATION

(PWM) OUTPUTS WITH TIMER1 AND

TIMER2

Three high speed pulse width modulation (PWM) out-

puts are provided. The PWM1 output uses Timer1 as

its time-base, while PWM2 and PWM3 may indepen-

dently be software conﬁgured to use either Timer1 or

Timer2 as the time-base. The PWM outputs are on the

RB2/PWM1, RB3/PWM2, and RG5/PWM3 pins.

Each PWM output has a maximum resolution of

10-bits. At 10-bit resolution, the PWM output frequency

is 32.2 kHz (@ 32 MHz clock) and at 8-bit resolution the

PWM output frequency is 128.9 kHz. The duty cycle of

the output can vary from 0% to 100%.

Figure 13-6 shows a simpliﬁed block diagram of a

PWM module.

The duty cycle registers are double buffered for glitch

free operation. Figure 13-7 shows how a glitch could

occur if the duty cycle registers were not double buff-

ered.

The user needs to set the PWM1ON bit (TCON2<4>)

to enable the PWM1 output. When the PWM1ON bit is

set, the RB2/PWM1 pin is conﬁgured as PWM1 output

and forced as an output irrespective of the data direc-

tion bit (DDRB<2>). When the PWM1ON bit is clear,

the pin behaves as a port pin and its direction is con-

trolled by its data direction bit (DDRB<2>). Similarly,

the PWM2ON (TCON2<5>) bit controls the conﬁgura-

tion of the RB3/PWM2 pin and the PWM3ON

(TCON3<0>) bit controls the conﬁguration of the

RG5/PWM3 pin.

FIGURE 13-6: SIMPLIFIED PWM BLOCK

DIAGRAM

PWxDCH

Duty Cycle registers

PWxDCL<7:6>

Clear Timer,

PWMx pin and

Latch D.C.

(Slave)

Comparator

TMRx

Comparator

PRy

(Note 1)

PWMxON

PWMx

Note 1: 8-bit timer is concatenated with 2-bit internal Q clock

or 2 bits of the prescaler to create 10-bit time-base.

Read

Write

FIGURE 13-7: PWM OUTPUT

1020

3040

PWM

output

Timer

interrupt

Write new

PWM value

Timer interrupt

new PWM value

transferred to slave

Note

The dotted line shows PWM output if duty cycle registers were not double buffered.

If the new duty cycle is written after the timer has passed that value, then the PWM does

not reset at all during the current cycle causing a “glitch”.

In this example, PWM period = 50. Old duty cycle is 30. New duty cycle value is 10.

PIC17C752-08/P Datasheet(PDF) 97 Page - Microchip Technology

PIC17C752-08/P Datasheet(HTML) 97 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL