TS80C31X2-VLED datasheet(29/42 Pages) ATMEL

29 / 42 page

Rev. C - 15 January, 2001

TS80C31X2

NOTES

ICC under reset is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns (see Figure 13.), VIL = VSS + 0.5 V,

VIH = VCC - 0.5V; XTAL2 N.C.; EA = RST = Port 0 = VCC. ICC would be slightly higher if a crystal oscillator used..

Idle ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH,TCHCL = 5 ns, VIL =VSS + 0.5 V, VIH =VCC - 0.5 V; XTAL2

N.C; Port 0 = VCC; EA = RST = VSS (see Figure 11.).

Power Down ICC is measured with all output pins disconnected; EA = VSS, PORT 0 = VCC; XTAL2 NC.; RST = VSS (see Figure 12.).

Capacitance loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the VOLs of ALE and Ports 1 and 3. The noise is

due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0 transitions during bus operation. In the worst

cases (capacitive loading 100pF), the noise pulse on the ALE line may exceed 0.45V with maxi VOL peak 0.6V. A Schmitt Trigger use is not necessary.

Typicals are based on a limited number of samples and are not guaranteed. The values listed are at room temperature and 5V.

Under steady state (non-transient) conditions, IOL must be externally limited as follows:

Maximum IOL per port pin: 10 mA

Maximum IOL per 8-bit port:

Port 0: 26 mA

Ports 1, 2 and 3: 15 mA

Maximum total IOL for all output pins: 71 mA

If IOL exceeds the test condition, VOL may exceed the related speciﬁcation. Pins are not guaranteed to sink current greater than the listed test conditions.

For other values, please contact your sales ofﬁce.

Operating ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns (see Figure 13.), VIL = VSS + 0.5 V,

VIH =VCC - 0.5V; XTAL2 N.C.; EA = Port 0 = VCC; RST = VSS. The internal ROM runs the code 80 FE (label: SJMP label). ICC would be slightly

higher if a crystal oscillator is used. Measurements are made with OTP products when possible, which is the worst case.

Figure 9. ICC Test Condition, under reset

ICC

idle

Power Supply Current Maximum values, X1

mode: (7)

0.15 Freq

(MHz) + 0.2

@12MHz 2

@16MHz 2.6

VCC = 3.3 V

(2)

Symbol

Parameter

Min

Typ

Max

Unit

Test Conditions

VCC

ICC

(NC)

CLOCK

SIGNAL

VCC

All other pins are disconnected.

RST

XTAL2

XTAL1

VSS

VCC

TS80C31X2-VLED Datasheet(PDF) 29 Page - ATMEL Corporation

TS80C31X2-VLED Datasheet(HTML) 29 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

Datasheet Download

Link URL