Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

L6235Q Datasheet(PDF) 18 Page - STMicroelectronics

Part # L6235Q
Description  Tacho output for speed loop
PDF  33 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  STMICROELECTRONICS [STMicroelectronics]
Direct Link  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

L6235Q Datasheet(HTML) 18 Page - STMicroelectronics

Back Button L6235Q Datasheet HTML 14Page - STMicroelectronics L6235Q Datasheet HTML 15Page - STMicroelectronics L6235Q Datasheet HTML 16Page - STMicroelectronics L6235Q Datasheet HTML 17Page - STMicroelectronics L6235Q Datasheet HTML 18Page - STMicroelectronics L6235Q Datasheet HTML 19Page - STMicroelectronics L6235Q Datasheet HTML 20Page - STMicroelectronics L6235Q Datasheet HTML 21Page - STMicroelectronics L6235Q Datasheet HTML 22Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 18 / 33 page
background image
Circuit description
L6235Q
18/33
Doc ID 018997 Rev 2
Figure 18.
tPULSE vs. CPUL and RPUL
4.7
Non-dissipative overcurrent detection and protection
The L6235Q integrates an overcurrent detection circuit (OCD) for full protection. With this
internal overcurrent detection, the external current sense resistor normally used and its
associated power dissipation are eliminated. Figure 19 shows a simplified schematic of the
overcurrent detection circuit.
To implement the overcurrent detection, a sensing element that delivers a small but precise
fraction of the output current is implemented with each high-side power MOSFET. Since this
current is a small fraction of the output current there is very little additional power
dissipation. This current is compared with an internal reference current IREF. When the
output current reaches the detection threshold (typically ISOVER = 5.6 A), the OCD
comparator signals a fault condition. When a fault condition is detected, an internal open
drain MOSFET with a pull-down capability of 4 mA connected to pin DIAG is turned on.
Pin DIAG can be used to signal the fault condition to a µC or to shut down the 3-phase
bridge simply by connecting it to pin EN and adding an external R-C (see REN, CEN).
0
0
1
0
1
1
10
100
1 .10
3
1 .10
4
Cpul [nF]
RPUL = 100kΩ
RPUL = 47kΩ
RPUL = 20kΩ



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com