PIC18F4520ESLASHMLQTP datasheet(211/390 Pages) MICROCHIP

211 / 390 page

 2004 Microchip Technology Inc.

Preliminary

DS39631A-page 209

PIC18F2420/2520/4420/4520

18.1.3

AUTO-BAUD RATE DETECT

The enhanced USART module supports the automatic

detection and calibration of baud rate. This feature is

active only in Asynchronous mode and while the WUE

bit is clear.

The automatic baud rate measurement sequence

(Figure 18-1) begins whenever a Start bit is received

and the ABDEN bit is set. The calculation is

self-averaging.

In the Auto-Baud Rate Detect (ABD) mode, the clock to

the BRG is reversed. Rather than the BRG clocking the

incoming RX signal, the RX signal is timing the BRG. In

ABD mode, the internal Baud Rate Generator is used

as a counter to time the bit period of the incoming serial

byte stream.

Once the ABDEN bit is set, the state machine will clear

the BRG and look for a Start bit. The Auto-Baud Rate

Detect must receive a byte with the value 55h (ASCII

“U”, which is also the LIN bus Sync character) in order to

calculate the proper bit rate. The measurement is taken

over both a low and a high bit time in order to minimize

any effects caused by asymmetry of the incoming signal.

After a Start bit, the SPBRG begins counting up, using

the preselected clock source on the first rising edge of

RX. After eight bits on the RX pin or the fifth rising edge,

an accumulated value totalling the proper BRG period is

left in the SPBRGH:SPBRG register pair. Once the 5th

edge is seen (this should correspond to the Stop bit), the

ABDEN bit is automatically cleared.

If a rollover of the BRG occurs (an overflow from FFFFh

to 0000h), the event is trapped by the ABDOVF status

bit (BAUDCON<7>). It is set in hardware by BRG roll-

overs and can be set or cleared by the user in software.

ABD mode remains active after rollover events and the

ABDEN bit remains set (Figure 18-2).

While calibrating the baud rate period, the BRG regis-

ters are clocked at 1/8th the preconfigured clock rate.

Note that the BRG clock will be configured by the

BRG16 and BRGH bits. Independent of the BRG16 bit

setting, both the SPBRG and SPBRGH will be used as

a 16-bit counter. This allows the user to verify that no

carry occurred for 8-bit modes by checking for 00h in

the SPBRGH register. Refer to Table 18-4 for counter

clock rates to the BRG.

While the ABD sequence takes place, the EUSART

state machine is held in Idle. The RCIF interrupt is set

once the fifth rising edge on RX is detected. The value

in the RCREG needs to be read to clear the RCIF

interrupt. The contents of RCREG should be discarded.

TABLE 18-4:

BRG COUNTER

CLOCK RATES

18.1.3.1

ABD and EUSART Transmission

Since the BRG clock is reversed during ABD acquisi-

tion, the EUSART transmitter cannot be used during

ABD. This means that whenever the ABDEN bit is set,

TXREG cannot be written to. Users should also ensure

that ABDEN does not become set during a transmit

sequence. Failing to do this may result in unpredictable

EUSART operation.

Note 1: If the WUE bit is set with the ABDEN bit,

Auto-Baud Rate Detection will occur on

the byte following the Break character.

2: It is up to the user to determine that the

incoming character baud rate is within the

range of the selected BRG clock source.

Some combinations of oscillator frequency

and EUSART baud rates are not possible

due to bit error rates. Overall system tim-

ing and communication baud rates must

be taken into consideration when using the

Auto-Baud Rate Detection feature.

BRG16

BRGH

BRG Counter Clock

FOSC/512

FOSC/128

FOSC/32

Note:

During the ABD sequence, SPBRG and

SPBRGH are both used as a 16-bit counter,

independent of BRG16 setting.

PIC18F4520E/MLQTP Datasheet(PDF) 211 Page - Microchip Technology

PIC18F4520E/MLQTP Datasheet(HTML) 211 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL