PIC24FJ128GL303 datasheet(76/424 Pages) MICROCHIP

76 / 424 page

PIC24FJ128GL306 FAMILY

DS30010198B-page 76

 2019-2020 Microchip Technology Inc.

RCON: RESET CONTROL REGISTER(6)

R/W-0

R/W-1

R/W-0

U-0

R/W-0

TRAPR(1)

IOPUWR(1)

SBOREN(5)

RETEN(2)

—

—CM(1)

VREGS(3)

bit 15

bit 8

R/W-0

R/W-1

EXTR(1)

SWR(1)

SWDTEN(4)

WDTO(1)

SLEEP(1)

IDLE(1)

BOR(1)

POR(1)

bit 7

bit 0

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

bit 15

TRAPR: Trap Reset Flag bit(1)

1 = A Trap Conflict Reset has occurred

0 = A Trap Conflict Reset has not occurred

bit 14

IOPUWR: Illegal Opcode or Uninitialized W Register Access Reset Flag bit(1)

1 = An illegal opcode detection, an illegal address mode or Uninitialized W register is used as an

Address Pointer and caused a Reset

0 = An illegal opcode or Uninitialized W register Reset has not occurred

bit 13

SBOREN: Software Control Over the BOR Function bit(5)

1 = BOR is enabled

0 = BOR is disabled

bit 12

RETEN: Retention Mode Enable bit(2)

1 = Retention mode is enabled while device is in Sleep mode (1.2V regulator supplies to the core)

0 = Retention mode is disabled; normal voltage levels are present

bit 11-10

Unimplemented: Read as ‘0’

bit 9

CM: Configuration Word Mismatch Reset Flag bit(1)

1 = A Configuration Word Mismatch Reset has occurred

0 = A Configuration Word Mismatch Reset has not occurred

bit 8

VREGS: Fast Wake-up from Sleep bit(3)

1 = Regulator Standby mode is disabled (fast wake-up, uses more power)

0 = Regulator Standby mode is enabled (slow wake-up, uses less power)

bit 7

EXTR: External Reset (MCLR) Pin bit(1)

1 = A Master Clear (pin) Reset has occurred

0 = A Master Clear (pin) Reset has not occurred

bit 6

SWR: Software RESET (Instruction) Flag bit(1)

1 = A RESET instruction has been executed

0 = A RESET instruction has not been executed

Note 1: All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not

cause a device Reset.

2: If the LPCFG Configuration bit is ‘1’ (unprogrammed), the retention regulator is disabled and the RETEN

bit has no effect.

3: Re-enabling the regulator after it enters Standby mode will add a delay, TVREG, when waking up from Sleep.

Applications that do not use the voltage regulator should set this bit to prevent this delay from occurring.

4: If the FWDTEN[1:0] Configuration bits are ‘11’ (unprogrammed), the WDT is always enabled, regardless of

the SWDTEN bit setting.

5: The BOREN[1:0] (FPOR[1:0]) Configuration bits must be set to ‘01’ in order for SBOREN to have an effect.

6: On wake-up from Retention Sleep, RCON will have same value as a POR event.

PIC24FJ128GL303 Datasheet(PDF) 76 Page - Microchip Technology

PIC24FJ128GL303 Datasheet(HTML) 76 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL