| Electronic Components Datasheet Search |
|
ADIS16IMU4PCBZ Datasheet(PDF) 4 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADIS16IMU4PCBZ Datasheet(HTML) 4 Page - Analog Devices |
|
4 / 34 page ![]() ADIS16467 Data Sheet Rev. C | Page 4 of 34 Parameter Test Conditions/Comments Min Typ Max Unit Bias In-Run Bias Stability 1 σ, y-axis and z-axis 13 μg Velocity Random Walk 1 σ 0.037 m/sec/√hr Repeatability1 −40°C ≤ TC ≤ +85°C, 1 σ ±6 mg Error over Temperature −40°C ≤ TC ≤ +85°C, 1 σ ±3 mg Output Noise No filtering 2.3 mg rms Noise Density Bandwidth = 10 Hz to 40 Hz, no filtering 100 μg/√Hz rms 3 dB Bandwidth 600 Hz Sensor Resonant Frequency Y-axis and z-axis 5.65 kHz X-axis 5.25 kHz TEMPERATURE SENSOR Scale Factor Output = 0x0000 at 0°C (±5°C) 0.1 °C/LSB LOGIC INPUTS4 Input Voltage High, VIH 2.0 V Low, VIL 0.8 V RST Pulse Width 1 μs CS Wake-Up Pulse Width 20 μs Input Current Logic 1, IIH VIH = 3.3 V 10 μA Logic 0, IIL VIL = 0 V All Pins Except RST 10 μA RST Pin 0.33 mA Input Capacitance, CIN 10 pF DIGITAL OUTPUTS Output Voltage High, VOH ISOURCE = 0.5 mA 2.4 V Low, VOL ISINK = 2.0 mA 0.4 V FLASH MEMORY Endurance5 10000 Cycles Data Retention6 TJ = 85°C 20 Years FUNCTIONAL TIMES7 Time until data is available Power-On Start-Up Time 259 ms Reset Recovery Time Register GLOB_CMD, Bit 7 = 1 (see Table 113) 198 ms RST pulled low, then restored to high8 198 ms Factory Calibration Restore Register GLOB_CMD, Bit 1 = 1 (see Table 113) 142 ms Flash Memory Backup Register GLOB_CMD, Bit 3 = 1 (see Table 113) 72 ms Flash Memory Test Time Register GLOB_CMD, Bit 4 = 1 (see Table 113) 32 ms Self Test Time9 Register GLOB_CMD, Bit 2 = 1 (see Table 113) 14 ms CONVERSION RATE 2000 SPS Initial Clock Accuracy 3 % Sync Input Clock 1.9 2.1 kHz POWER SUPPLY, VDD Operating voltage range 3.0 3.6 V Power Supply Current10 Normal mode, VDD = 3.3 V 44 55 mA 1 Bias repeatability provides an estimate for long-term drift in the bias, as observed during 500 hours of High-Temperature Operating Life (HTOL) at +105°C. 2 This measurement is based on the deviation from a best fit linear model. 3 All specifications associated with the accelerometers relate to the full-scale range of ±40 g, unless otherwise noted. 4 The digital input/output signals use a 3.3 V system. 5 Endurance is qualified as per JEDEC Standard 22, Method A117, measured at −40°C, +25°C, +85°C, and +125°C. 6 The data retention specification assumes a junction temperature (TJ) of 85°C per JEDEC Standard 22, Method A117. Data retention lifetime decreases with TJ. 7 These times do not include thermal settling and internal filter response times, which may affect overall accuracy. 8 The RST line must be in a low state for at least 10 μs to ensure a proper reset initiation and recovery. 9 The self test time can extend when using external clock rates lower than 2000 Hz. 10 Power supply current transients can reach 100 mA during initial startup or reset recovery. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |