ICL7117CSLASHD datasheet(3/8 Pages) MAXIM

3 / 8 page

This device conforms to the Absolute Maximum Ratings on adjacent page.

● Guaranteed Overload Recovery Time

● Significantly Improved ESD Protection (Note 8)

● Low Noise

● Key Parameters Guaranteed Over Temperature

● Negligible Hysteresis

● Maxim Quality and Reliability

● Increased Maximum Rating for Input Current (Note 9)

Note 3: Unless otherwise noted, specifications apply to both the ICL7116 and ICL7117 at TA = +25°C, fCLOCK = 48kHz. ICL7116 is

tested in the circuit of Figure 1. ICL7117 is tested in the circuit of Figure 2.

Note 4: Refer to “Differential input” discussion (see Maxim’s ICL7106/ICL7107 data sheet).

Note 5: Backplane drive is in phase with segment drive for ‘off’ segment, 180º out of phase for on segment. Frequency is 20 times

the conversion rate. Average DC component is less than 50mV.

Note 6: The ICL7116 logic input has an internal pulldown resistor connected from HLDR, pin 1, to TEST, pin 37. The ICL7117 logic

input has an internal pulldown resistor connected from HLDR. Pin 1, to GROUND, pin 21.

(Specifications below satisfy or exceed all ‘tested’ parameters on adjacent page V+ = 9V, TA = +25ºC, fCLOCK = 48kHz; test circuit =

Figure 1 (ICL7116), Figure 2 (ICL7117), unless otherwise noted.)

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

Zero Input Reading

VIN = 0V

Full Scale = 200.00mV

TA = +25°C (Note 7)

-000.0

±000.0 +000.0

Digital

Reading

0°C ≤ TA ≤ +70°C (Note 11)

-000.0

±000.0 +000.0

Ratiometric Reading

VIN = VREF = 100mV

TA = +25°C (Note 7)

999

999/

1000

Digital

Reading

0°C ≤ TA ≤ +70°C (Note 11)

999

999/

1000

1001

Rollover Error (Difference in Reading for

Equal Positive and Negative Reading Near

Full Scale)

-VIN = +VIN = 200mV

TA = +25°C (Note 7)

-1

±0.2

Counts

0°C ≤ TA ≤ +70°C (Note 11)

±0.2

Linearity (Max. Deviation from Best Straight

Line Fit)

Full Scale = 200mV

or Full Scale = 2.00mV

-1

±0.2

Counts

PARAMETER

CONDITIONS

MIN

TYP

MAX

VIL, Pin 1 (ICL7117 Only)

GND +1.5

VIH, Pin 1 (Both)

V+ - 1.5

ICL7116 Only (Note 5)

Pk-Pk Segment Drive Voltage,

Pk-Pk Backplane Drive Voltage

V+ to V- = 9V

ICL7117 Only (Except Pin 19) Segment

Sinking Current

V+ = 5.0V

Segment Voltage = 3V

8.0

(Pin 19 Only)

ICL7116/ICL7117

3½ Digit ADCs with Display Hold

www.maximintegrated.com

Maxim Integrated │ 3

Absolute Maximum Ratings

Electrical Characteristics (continued) (Note 3)

Maxim Advantages

Electrical Characteristics

ICL7117C/D Datasheet(PDF) 3 Page - Maxim Integrated Products

ICL7117C/D Datasheet(HTML) 3 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8

Datasheet Download

Link URL