Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

DRV104PWPR Datasheet(PDF) 4 Page - Texas Instruments

Part # DRV104PWPR
Description  1.2A PWM High-Side Driver for Solenoids, Coils, Valves, Heaters, and Lamps
PDF  25 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI2 [Texas Instruments]
Direct Link  https://www.ti.com
Logo TI2 - Texas Instruments

DRV104PWPR Datasheet(HTML) 4 Page - Texas Instruments

  DRV104PWPR Datasheet HTML 1Page - Texas Instruments DRV104PWPR Datasheet HTML 2Page - Texas Instruments DRV104PWPR Datasheet HTML 3Page - Texas Instruments DRV104PWPR Datasheet HTML 4Page - Texas Instruments DRV104PWPR Datasheet HTML 5Page - Texas Instruments DRV104PWPR Datasheet HTML 6Page - Texas Instruments DRV104PWPR Datasheet HTML 7Page - Texas Instruments DRV104PWPR Datasheet HTML 8Page - Texas Instruments DRV104PWPR Datasheet HTML 9Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 4 / 25 page
background image
DRV104
4
SBVS036B
www.ti.com
PIN
NAME
DESCRIPTION
1
Duty Cycle Adjust
Internally, this pin connects to the input of a comparator and a (2.75 x IREF) current source from VS. The voltage at this node linearly
sets the duty cycle. The duty cycle can be programmed with a resistor, analog voltage, or the voltage output of a D/A converter. The
active voltage range is from 1.3V to 3.9V to facilitate the use of single-supply control electronics. At 3.56V, the output duty cycle is
near 90%. At 1.5V, the output duty cycle is near 10%. Internally, this pin is forced to 1.24V. No connection is required when the device
is in slave mode.
2
Delay Adjust
This pin sets the duration of the initial 100% duty cycle before the output goes into PWM mode. Leaving this pin floating results in
a delay of approximately 18
µs, which is internally limited by parasitic capacitance. Minimum delay may be reduced to less than 3µs
by tying the pin to 5V. This pin connects internally to a 15
µA current source from V
S and to a 2.6V threshold comparator. When the
pin voltage is below 2.6V, the output device is 100% On. The PWM oscillator is not synchronized to the Input (pin 1), so the duration
of the first pulse may be any portion of the programmed duty cycle. No connection is required when the device is in slave mode.
3
Oscillator
PWM frequency is adjustable. A resistor to ground sets the current IREF and the internal PWM oscillator frequency. A range of 500Hz
Frequency Adjust
to 100kHz can be achieved with practical resistor values. Although oscillator frequency operation below 500Hz is possible, resistors
higher than 10M
Ω will be required. The pin then becomes a very high-impedance node and is, therefore, sensitive to noise pickup
and PCB leakage currents. Resistor connection to this pin in slave mode sets the frequency at which current limit reset occurs.
4
Master
With no connection, this pin is driven to 5V by an internal 15
µA current source. In this mode the device is the master and the SYNC
pin becomes a 0V to 4.2V output, which is High when the power device is on. When the Master/Input is 0V, the SYNC pin is an
input. In slave mode, the output follows the SYNC pin; the output is High when SYNC is High.
5
BOOT
The bootstrap capacitor between this pin and the output, supplies the charge to provide the VGS necessary to turn on the power
device. CBOOT should be larger than 100pF. Use of a smaller CBOOT may slow the output rise time, device is specified and tested
with 470pF.
6, 7
OUT1, OUT2
The output is the source of a power DMOS transistor with its drain connected to VPS. Its low on-resistance (0.45Ω typ) assures
low power dissipation in the DRV104. Gate drive to the power device is controlled to provide a slew-rate limited rise-and-fall time.
This reduces the radiated RFI/EMI noise. A flyback diode is needed with inductive loads to conduct the load current during the off
cycle. The external diode should be selected for low forward voltage and low storage time. The internal diode should not be used
as a flyback diode. If devices are connected in parallel, the outputs must be connected through individual diodes. Devices are
current-limit protected for shorts to ground, but not to supply.
8, 9
VPS1, VPS2
These are the load power-supply pins to the drain of the power device. The load supply voltage may exceed the voltage at pin 10
by 5V, but must not exceed 37V.
10
+VS
This is the power-supply connection for all but the drain of the power device. The operating range is 8V to 32V.
11
GND
This pin must be connected to the system ground for the DRV104 to function. It does not carry the load current when the power
DMOS device is switched on.
12
SYNC
The SYNC pin is a 0V to 4.2V copy of the output when the Master/Slave pin is High. As an output, it can supply 100
µA with 1kΩ
output resistance. At 2mA, it current limits to either 4.2V or 0V. When the Master pin is Low, it is an input and the threshold is 2V.
SYNC output follows power output in master mode, and is not affected by thermal or current-limit shutdown. Power output follows
SYNC input in slave mode.
13
Status OK Flag
Normally High (active Low), a Flag Low signals either an over-temperature or over-current fault. A thermal fault (thermal shutdown)
occurs when the die surface reaches approximately 160
°C and latches until the die cools to 140°C. This output requires a pull-
up resistor and it can typically sink 2mA, sufficient to drive a low-current LED. Sink current is internally limited at 10mA, typical.
14
Input
The input is compatible with standard TTL levels. The device becomes enabled when the input voltage is driven above the typical
switching threshold, 1.8V; below this level, the device is disabled. Input current is typically 1
µA when driven High and 1µA when driven
Low. The input should not be directly connected to the power supply (VS) or damage will occur.
PIN DESCRIPTIONS
PIN CONFIGURATION
Top View
HTSSOP
Duty Cycle Adj
Delay Adj
Osc Freq Adj
Master
Boot
OUT1
OUT2
Input
Status OK Flag
SYNC
GND
+V
S
V
PS1
V
PS2
1
2
3
4
5
6
7
14
13
12
11
10
9
8
DRV104
PowerPAD
Duty Cycle Adj
Delay Adj
Osc Freq Adj
GND
Input
Status OK Flag
+V
S
OUT
1
3
5
7
14
12
10
8
DRV103
PowerPAD
DRV103 for Reference
Top View
SO



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com