| Electronic Components Datasheet Search |
|
DRV104PWPR Datasheet(PDF) 9 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
DRV104PWPR Datasheet(HTML) 9 Page - Texas Instruments |
|
9 / 25 page ![]() DRV104 9 SBVS036B www.ti.com DUTY CYCLE RPWM (Ω) (Nearest 1% Values) (%) 5kHz 25kHz 100kHz 10 412k 84.5k 25.5k 20 487k 97.6k 28.7k 30 562k 113k 31.6k 40 649k 130k 35.7k 50 715k 147k 39.2k 60 787k 162k 43.2k 70 887k 174k 44.9k 80 953k 191k — 90 1050k 205k — FIGURE 6. Using a Resistor to Program Duty Cycle. FIGURE 5. Output Waveform at High Load Current. FIGURE 7. Using a Voltage to Program Duty Cycle. DUTY CYCLE VPWM (%) (V) 10 1.501 20 1.773 40 2.296 60 2.813 80 3.337 90 3.589 TABLE IV. Duty Cycle Adjust Voltage. TABLE III. Duty Cycle Adjust Resistance. ADJUSTABLE DUTY CYCLE (PWM MODE) The DRV104’s externally adjustable duty cycle provides an accurate means of controlling power delivered to a load. Duty cycle can be set over a range of 10% to 90% with an external resistor, analog voltage, or the voltage output of a D/A converter. A low duty cycle results in reduced power dissipation in the load. This keeps the DRV104 and the load cooler, resulting in increased reliability for both devices. Resistor Controlled Duty Cycle Duty cycle is easily programmed by connecting a resistor (RPWM) between Duty Cycle Adjust (pin 1) and ground. High resistor values correspond to high duty cycles. At 100kHz, the range of adjustable duty cycle is limited to 10% to 70%. Table III provides resistor values for typical duty cycles. Resistor values for additional duty cycles can be obtained from Figure 6. Voltage Controlled Duty Cycle The duty cycle can also be programmed by analog voltage VPWM. With VPWM ≈ 3.59V, the duty cycle is about 90%. Decreasing this voltage results in decreased duty cycles. Table IV provides VPWM values for typical duty cycles. Figure 7 shows the relationship of duty cycle versus VPWM and its linearity. 10M 1M 100k 10k 20 40 0 60 80 100 DUTY CYCLE vs R PWM Duty Cycle (%) 5kHz 25kHz 100kHz R PWM (kΩ) = 334.35 + 7.75(%DC) R PWM (kΩ) = 68.73 + 1.52(%DC) R PWM (kΩ) = 20.62 + 0.39(%DC) R FREQ only With 100pF in Parallel with R FREQ Time (10 µs) 100 90 80 70 60 50 40 30 20 10 0 2 1 2.0 1.5 1.0 0.5 0 –0.5 –1.0 –1.5 –2.0 34 DUTY CYCLE AND DUTY CYCLE ERROR vs VOLTAGE V PWM (V) Duty Cycle Duty Cycle Error At V S = 24V and F = 25kHz: VPWM = 1.25 + 0.026 × %DC |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |