| Electronic Components Datasheet Search |
|
DRV104PWPR Datasheet(PDF) 13 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
DRV104PWPR Datasheet(HTML) 13 Page - Texas Instruments |
|
13 / 25 page ![]() DRV104 13 SBVS036B www.ti.com BYPASSING A 1 µF ceramic bypass capacitor is adequate for uniform duty cycle control when switching loads of less than 0.5A. Larger bypass capacitors are required when switching high-current loads. A 10 µF ceramic capacitor is recommended for heavy- duty (1.2A) applications. It may also be desirable to run the DRV104 and load driver on separate power supplies at high- load currents. Bypassing is especially critical near the abso- lute maximum supply voltage of 32V. In the event of a current overload, the DRV104 current limit responds in microsec- onds, dropping the load current to zero. With inadequate bypassing, energy stored in the supply line inductance can lift the supply sufficiently to exceed voltage breakdown with catastrophic results. Place the flyback diode at the DRV104 end when driving long (inductive) cables to a remotely located load. This minimizes RFI/EMI and helps protect the output DMOS transistor from breakdown caused by dI/dt transients. Fast rectifier diodes such as epitaxial silicon or Schottky types are recommended for use as flyback diodes. APPLICATIONS CIRCUITS SINGLE AND MULTICHANNEL The DRV104 can be used in a variety of ways with resistive and inductive loads. As a single-channel driver, it can be placed on one PC board or inside a solenoid, relay, actuator, valve, motor, heater, thermoelectric cooler, or lamp housing. In high-density systems, multichannel power drivers may be packed close together on a PC board. For these switching applications, it is important to provide power supply bypass- ing as close to the driver IC as possible to avoid cross- coupling of spikes from one circuit to another. Also, in some applications, it may be necessary to keep beat frequencies (sum and difference between DRV oscillators or between DRV oscillators and system clock frequencies) from interfer- ing with low-level analog circuits that are located relatively near to the power drivers. Paralleling device outputs is not recommended as unequal load sharing and device damage will result. BEAT FREQUENCIES IN NON-SYNCHRONIZED MULTICHANNEL SYSTEMS In many multichannel systems, beat frequencies are of no consequence where each DRV uses its own internal oscilla- tor. Beat frequencies can be intentionally set up to be outside the measurement base-band to avoid interference in sensitive analog circuits located nearby. For example, with two DRV104s, a beat frequency of 22.5kHz can be established by setting one internal oscillator to a center of 62.5kHz and the other to 40kHz. Considering the specification of ±20% frequency accuracy, the beat could range from 2kHz (48kHz and 50kHz) to 43kHz (75kHz and 32kHz). By limiting the analog measurement bandwidth to 100Hz, for example, interference can be avoided. BEAT FREQUENCY ELIMINATION—OPTIONAL SYNCHRONIZATION The benefit of synchronization in multichannel systems is that measurement interference can be avoided in low-level analog circuits, particularly when physically close to the DRVs. Specifically, synchronization will accomplish the fol- lowing: 1. Eliminate beat frequencies between DRVs or DRVs and the system clock. 2. Predict quiet or non-switching times. Synchronization of DRV104s is possible by using one oscil- lator frequency for all DRVs. See Figure 15 for an example of one DRV internal oscillator as the master and the others as slaves. Also, one external clock can be used as the master and all the others as slaves. PEAK SUPPLY CURRENT ELIMINATION—OPTIONAL SWITCHING SKEW In many systems, particularly where only a few channels are used or low magnitude load currents are present, it is unnecessary to skew the switching times. In some multichannel systems, where just PWM is used, without initial dc time delay, simultaneous switching of edges can cause large peak currents to be drawn from the main power supply. This is similar to that which occurs when multiple switching power supplies draw current from one power source. Peak currents can be reduced by synchronizing oscillators and skewing switching edges. Synchronization has the added benefit of eliminating beat frequencies, as discussed above. Skewing can be accomplished by using a polyphase clock approach, which intentionally delays the time that each DRV switches on PWM edges. The DRV104 is useful for a variety of relay driver applications (see Figures 16 and 17), as well as valve drivers (see Figures 18 and 19). |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |