| Electronic Components Datasheet Search |
|
SPC574KX Datasheet(PDF) 71 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
SPC574KX Datasheet(HTML) 71 Page - STMicroelectronics |
|
71 / 160 page ![]() DocID023601 Rev 6 71/160 SPC574Kx Electrical characteristics 159 Figure 17. S/D impedance generic model 11. S/D ADC is functional in the range 3.0 – 4.5 V, SNR parameter degrades by 9 dB. Degraded SNR value based on simulation. 12. This parameter is guaranteed by bench validation with a small sample of devices across process variations. 13. Input impedance is valid over the full input frequency range.Input impedance is calculated in megaohms by the formula 25.6/(Gain * fADCD_M). 14. Impedance given at FADCD_M = 16MHz. Impedance is inversely proportional to frequency: ZDIFF(FADCD_M) = 16MHz/FADCD_M*ZDIFF 15. Impedance given at FADCD_M = 16MHz. Impedance is inversely proportional to frequency: ZCM(FADCD_M) = 16MHz/FADCD_M*ZCM 16. SNR values guaranteed only if external noise on the ADC input pin is attenuated by the required SNR value in the frequency range of fADCD_M – fADCD_S to fADCD_M + fADCD_S, where fADCD_M is the input sampling frequency, and fADCD_S is the output sample frequency. A proper external input filter should be used to remove any interfering signals in this frequency range. 17. The ±1% passband ripple specification is equivalent to 20 * log10 (0.99) = 0.087 dB. 18. Propagation of the information from the pin to the register CDR[CDATA] and flags SFR[DFEF], SFR[DFFF] is given by the different modules that need to be crossed: delta/sigma filters, high pass filter, fifo module, clock domain synchronizers. The time elapsed between data availability at pin and internal S/D module registers is given by the below formula: REGISTER LATENCY = tLATENCY + 0.5/fADCD_S + 2 (~+1)/fADCD_M + 2(~+1)fPBRIDGEx_CLK where fADCD_S is the frequency of the sampling clock, fADCD_M is the frequency of the modulator, and fPBRIDGEx_CLK is the frequency of the peripheral bridge clock feeds to the ADC S/D module. The (~+1) symbol refers to the number of clock cycles uncertainty (from 0 to 1 clock cycle) to be added due to resynchronization of the signal during clock domain crossing. Some further latency may be added by the target module (core, DMA, interrupt) controller to process the data received from the ADC S/D module. 19. This capacitance does not include pin capacitance, that can be considered together with external capacitance, before sampling switch. 20. Consumption is given after power-up, when steady state is reached. Extra consumption up to 2 mA may be required during internal circuitry set-up. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |