R5F5671CDDFM datasheet(84/179 Pages) RENESAS

84 / 179 page

R01DS0373EJ0120 Rev.1.20

Page 84 of 179

Sep 30, 2024

RX671 Group

2. Electrical Characteristics

Note 1. Supply current values are measured when all output pins are unloaded and all input pull-up resistors are disabled.

Table 2.6

DC Characteristics (3)

Conditions: VCC = AVCC0 = AVCC1 = VCC_USB = 2.7 to 3.6 V, 2.7 V ≤ VREFH0 ≤ AVCC0,

VSS = AVSS0 = AVSS1 = VREFL0 = VSS_USB = 0 V,

Ta = Topr

Item

Symbol

D version

G version

Unit

Test Conditions

Typ.

Max.

Typ.

Max.

Supply

current*1

Full operation*2

ICC*3

—

ICLK = 120 MHz,

PCLKA = 120 MHz,

PCLKB = 60 MHz,

PCLKC = 60 MHz,

PCLKD = 60 MHz,

FCLK = 60 MHz,

BCLK = 120 MHz,

BCLK pin = 60 MHz

Normal

operation

Peripheral module clocks are supplied

—

Peripheral module clocks are stopped

*4, *5

—

Core

Mark

Peripheral module clocks are stopped

*4, *5

14.5

—

14.5

—

Sleep mode: Peripheral module clocks are

supplied*4

All module clock stop mode (reference value)

Increased by BGO

operation*8

Reading from the code flash

memory while the data flash

memory is being

programmed

6—

—

Reading from the code flash

memory while the code flash

memory is being

programmed

7—

—

Increased by Trusted Secure IP operation

—

Low-speed operating mode 1: Peripheral module clocks

are stopped*4

1.6

—

1.6

—

All clocks 1 MHz

Low-speed operating mode 2: Peripheral module clocks

are stopped*4

1.6

—

1.6

—

All clocks 32.768

kHz

Software standby mode

1.1

Power is supplied to the standby RAM, USB

resume detecting unit (USB0 only) and REMC

15.5

µA

Power is not

supplied to the

standby RAM,

USB resume

detecting unit

(USB0 only) and

REMC

Low power consumption

function of the power-on reset

circuit is disabled*6

11.5

Low power consumption

function of the power-on reset

circuit is enabled*7

4.9

Increase current

by operating RTC

Drive capacity for low CL is

set in RCR3.RTCDV[2:0].

1—

—

Drive capacity for standard CL

is set in RCR3.RTCDV[2:0].

2—

—

Increase current

by operating

REMC

External clock (32 kHz) input

0.1

—

0.1

—

Drive capacity for standard CL

is set in RCR3.RTCDV[2:0].

1.4

—

1.4

—

When the RTC is

operating while VCC is

not supplied (Only the

RTC and sub-clock

oscillator operate with

the battery backup

function)

Drive capacity for low CL is

set in RCR3.RTCDV[2:0].

0.9

—

0.9

—

VBATT = 2.0 V,

VCC = 0 V

1.6

—

1.6

—

VBATT = 3.3 V,

VCC = 0 V

Drive capacity for standard CL

is set in RCR3.RTCDV[2:0].

1.6

—

1.6

—

VBATT = 1.62 V,

VCC = 0 V

1.7

—

1.7

—

VBATT = 2.0 V,

VCC = 0 V

3.3

—

3.3

—

VBATT = 3.3 V,

VCC = 0 V

Inrush current on

release from deep

software standby mode

Inrush current*9

IRUSH

—

130

—

130

Total inrush current*9

ERUSH

—1

µC

R5F5671CDDFM Datasheet(PDF) 84 Page - Renesas Technology Corp

R5F5671CDDFM Datasheet(HTML) 84 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL