TMS320LF2407 datasheet(46/106 Pages) TI

46 / 106 page

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443

• HOUSTON, TEXAS 77251–1443

serial peripheral interface (SPI) module

Some ’240x devices include the four-pin serial peripheral interface (SPI) module. The SPI is a high-speed,

synchronous serial I/O port that allows a serial bit stream of programmed length (one to sixteen bits) to be shifted

into and out of the device at a programmable bit-transfer rate. Normally, the SPI is used for communications

between the DSP controller and external peripherals or another processor. Typical applications include external

I/O or peripheral expansion through devices such as shift registers, display drivers, and ADCs. Multidevice

communications are supported by the master/slave operation of the SPI.

The SPI module features include:

D Four external pins:

–

SPISOMI: SPI slave-output/master-input pin

–

SPISIMO: SPI slave-input/master-output pin

–

SPISTE: SPI slave transmit-enable pin

–

SPICLK: SPI serial-clock pin

NOTE: All four pins can be used as GPIO, if the SPI module is not used.

D Two operational modes: master and slave

D Baud rate: 125 different programmable rates/7.5 Mbps at 30-MHz CPUCLK

D Data word length: one to sixteen data bits

D Four clocking schemes (controlled by clock polarity and clock phase bits) include:

–

Falling edge without phase delay: SPICLK active high. SPI transmits data on the falling edge of the

SPICLK signal and receives data on the rising edge of the SPICLK signal.

–

Falling edge with phase delay: SPICLK active high. SPI transmits data one half-cycle ahead of the

falling edge of the SPICLK signal and receives data on the falling edge of the SPICLK signal.

–

Rising edge without phase delay: SPICLK inactive low. SPI transmits data on the rising edge of the

SPICLK signal and receives data on the falling edge of the SPICLK signal.

–

Rising edge with phase delay: SPICLK inactive low. SPI transmits data one half-cycle ahead of the

falling edge of the SPICLK signal and receives data on the rising edge of the SPICLK signal.

D Simultaneous receive and transmit operation (transmit function can be disabled in software)

D Transmitter and receiver operations are accomplished through either interrupt-driven or polled algorithms.

D Nine SPI module control registers: Located in control register frame beginning at address 7040h.

NOTE: All registers in this module are 16-bit registers that are connected to the 16-bit peripheral bus. When a register is accessed, the

register data is in the lower byte (7 – 0), and the upper byte (15 – 8) is read as zeros. Writing to the upper byte has no effect.

TMS320LF2407 Datasheet(PDF) 46 Page - Texas Instruments

TMS320LF2407 Datasheet(HTML) 46 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL