WM8143-10CFTSLASHV datasheet(17/24 Pages) WOLFSON

17 / 24 page

Production Data

WM8143-10

Wolfson Microelectronics

PD.Rev 3f June 98

Applications Recommendations

Output Data Interface

By default, data is output from the device as a ten-bit

wide word on OP[9:0]. Optionally, data can be output in

an eight-bit word format. Figure 15 shows this function.

Data is presented on pins OP[9:2] at twice pixel rate.

In mode 3, the output is spread over three MCLK

periods. The first two periods contain byte A data and

the third period has byte B data. Either of the two byte

A data periods are valid.

Figure 15 Eight-bit Multiplexed Bus Output

•

A =d9,d8,d7,d6,d5,d4,d3,d2 - First byte

•

B =d1,d0,X,X,PNS,CC1,CC0,ORNG - Second byte

•

PNS : This bit shows if the device is configured in

parallel or serial mode. 1 = Parallel, 0 = Serial.

•

CC1/CC0 : These bits show which channel the

current output was taken from. 00 = RED, 01 =

GREEN, 10 = BLUE.

•

ORNG : This bit indicates if the current output pixel

has exceeded the maximum or minimum range

during processing. 1 = out of range, 0 = within range.

•

X: This is an invalid output.

Control Interface Selection

WM8143-10 can be controlled via a serial or parallel

interface. The decision on which interface is to be used

is made on the sense of the SEN/STB pin on the rising

edge of the NRESET signal.

SEN/STB

CONDITION

MODE

NRESET rising edge

Serial Interface

NRESET rising edge

Parallel Interface

Table 4 WM8143-10 Interface Set-up

It is expected that this would be achieved on system

power-up by attaching a simple RC network to the

NRESET pin. The RC network should delay the set-up

on the NRESET pin until the other conditions have

been established. This feature is only activated on a

hardware reset (using the NRESET pin). The software

reset does not sample SEN/STB.

Controlling the WM8143-10

The WM8143-10 can be configured through a serial

interface or a parallel interface. Selection of the

interface type is by the SEN/STB pin which must be

tied high (parallel) or low (serial) as shown in Table 4.

Serial Interface

The serial interface consists of three pins (refer to

Figure 16). A six-bit address is clocked in MSB first

followed by an eight-bit data word, also MSB first. Each

bit is latched on the rising edge of SCK. Once the data

has been shifted into the device, a pulse is applied to

SEN to transfer the data to the appropriate internal

Parallel Interface

The parallel interface uses bits [9:2] of the OP bus as

well as the STB, DNA and RNW pins (refer to Figure

17). Pin RNW must be low during a write operation.

The DNA pin defines whether the data byte is address

(low) or data (high). The data bus OP[9:2] is latched in

during the low period of STB.

Internal Register Definition

Table 5 summarises the internal register content. The

first 5 addresses in the table are used to program setup

registers and to provide a software reset feature (00H

is reserved). The remaining 3 entries in the table define

the address location of internal data registers. In each

case, a further three sub-addresses are defined for the

red, green and blue register. Selection between the red,

green and blue registers is performed by address bits

a1 and a0, as defined in the table. Setting both a1 and

a0 equal to 1 forces all three registers to be updated to

the same data value. Blank entries in Table 5 should be

programmed to zero.

a2 a1

a0 b7

b3 b2

b1 b0

SCK

SDI

SEN

Data Word

Address

Figure 16 Serial Interface Timing

MCLK

OP[9:2]

WM8143-10CFT/V Datasheet(PDF) 17 Page - Wolfson Microelectronics plc

WM8143-10CFT/V Datasheet(HTML) 17 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datasheet Download

Link URL