| Electronic Components Datasheet Search |
|
PIC18F23K22-E/ML Datasheet(PDF) 295 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F23K22-E/ML Datasheet(HTML) 295 Page - Microchip Technology |
|
295 / 496 page ![]() 2010 Microchip Technology Inc. Preliminary DS41412C-page 295 PIC18(L)F2X/4XK22 17.2 ADC Operation 17.2.1 STARTING A CONVERSION To enable the ADC module, the ADON bit of the ADCON0 register must be set to a ‘1’. Setting the GO/ DONE bit of the ADCON0 register to a ‘1’ will, depend- ing on the ACQT bits of the ADCON2 register, either immediately start the Analog-to-Digital conversion or start an acquisition delay followed by the Analog-to- Digital conversion. Figure 17-3 shows the operation of the A/D converter after the GO bit has been set and the ACQT<2:0> bits are cleared. A conversion is started after the following instruction to allow entry into SLEEP mode before the conversion begins. Figure 17-4 shows the operation of the A/D converter after the GO bit has been set and the ACQT<2:0> bits are set to ‘010’ which selects a 4 TAD acquisition time before the conversion starts. FIGURE 17-3: A/D CONVERSION TAD CYCLES (ACQT<2:0> = 000, TACQ = 0) FIGURE 17-4: A/D CONVERSION TAD CYCLES (ACQT<2:0> = 010, TACQ = 4 TAD) Note: The GO/DONE bit should not be set in the same instruction that turns on the ADC. Refer to Section 17.2.10 “A/D Conver- sion Procedure”. TAD1 TAD2 TAD3 TAD4 TAD5 TAD6 TAD7 TAD8 TAD11 Set GO bit Holding capacitor is disconnected from analog input (typically 100 ns) TAD9 TAD10 TCY - TAD ADRESH:ADRESL is loaded, GO bit is cleared, ADIF bit is set, holding capacitor is connected to analog input. Conversion starts b0 b9 b6 b5 b4 b3 b2 b1 b8 b7 On the following cycle: 2 TAD Discharge 1 2 3 4 5 6 7 8 11 Set GO bit (Holding capacitor is disconnected from analog input) 9 10 Conversion starts 1 2 3 4 (Holding capacitor continues acquiring input) TACQT Cycles TAD Cycles Automatic Acquisition Time b0 b9 b6 b5 b4 b3 b2 b1 b8 b7 ADRESH:ADRESL is loaded, GO bit is cleared, ADIF bit is set, holding capacitor is connected to analog input. On the following cycle: 2 TAD Discharge |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |