SPC564L54L5 datasheet(156/160 Pages) STMICROELECTRONICS

156 / 160 page

Revision history

SPC56XL60/54

156/160

Doc ID 15457 Rev 8

01-Aug-2012

Editorial changes.

In the “Block diagram” section, removed one PMU from the figure.

In the 257-pin pinout figure, changed cut2 to cut2/3 in Notes.

In the pin function summary table, changed cut2 to cut2/3.

In the “System pins” table:

– Added Note regarding Open Drain Enable.

– Added description to RESET pin.

In the pin-muxing table:

– Added Note about Open Drain.

– Changed cut2 to cut2/3.

– Changed all entries of column 'Weak pull config during reset’ to ' - ' , except

for PCR[2], PCR[3], PCR[4] and PCR[21].

In the “Absolute maximum ratings” table:

– Removed the “VSS_HV_REG” row.

– Added the footnote “Internal structures hold the input voltage...” to the VIN

maximum specifications.

In the “Recommended operating conditions” table, removed the “VSS_HV_REG”

row.

In the “Thermal characteristics” section:

– Added the “Thermal characteristics for LQFP100 package“ table.

– Updated values and footnote 1 in the 144 package table.

– Updated footnote 1 in the 257 package table.

In the “Supply current characteristics“ table:

– Added footnote 1 to parameter “IDD_LV_TYP + IDD_LV_PLL“ (symbol “T”).

– Changed “IDD_LV_STOP” at 150C from 80mA to 72mA.

– Changed “IDD_LV_HALT” at 150C from 72mA to 80mA.

In the “FMPLL electrical characteristics” table:

– Deleted the footnote “This value is true when operating at frequencies above

60 MHz...” from the specification for fCS and fDS.

– Changed “fSYS” to “fFMPLLOUT” in the entries for the CJITTER, fLCK, fUL, fCS,

and fDS specifications.

In the “ADC conversion characteristics” table:

– Revised the entry for TUEIS1WINJ (was P/T and “Total unadjusted error for

IS1WINJ”, is T and “Total unadjusted error for IS1WINJ (single ADC

channels)”).

– Revised the entry for TUEIS1WWINJ (was “Total unadjusted error for

IS1WWINJ”, is “Total unadjusted error for IS1WWINJ (double ADC

channels)”).

In the “Temperature sensor electrical characteristics“ table, for TJ = TA to

125 °C, changed Min/Max from values -7/+7 to -10/+10.

In the “Input Impedance and ADC Accuracy“ section:

– Changed CS in the text from 3 pF to 7.5 pF.

– Changed Req in the text from 330 kΩ to 133 kΩ.

–Removed RL, RSW, and RAD from the external network design constraint

equation and the sentence immediately preceding it.

– Changed the CF constraint value equation constant from 2048 to 8192.

In the “ADC conversion characteristics“ table, changed INL Min/Max values

from -2/+2 to -3/+3.

Table 44.

Document revision history (continued)

Date

Revision

Changes

SPC564L54L5 Datasheet(PDF) 156 Page - STMicroelectronics

SPC564L54L5 Datasheet(HTML) 156 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL