PIC16LC712 datasheet(77/106 Pages) MICROCHIP

77 / 106 page

 1999-2013 Microchip Technology Inc.

DS41106C-page 77

PIC16C712/716

12.3

DC Characteristics: PIC16C712/716-04 (Commercial, Industrial, Extended)

PIC16C712716-20 (Commercial, Industrial, Extended)

PIC16LC712/716-04 (Commercial, Industrial)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature

0°C

 TA 

+70°C

for commercial

-40°C

 TA 

+85°C

for industrial

-40°C

 TA  +125°C for extended

Operating voltage VDD range as described in DC spec Section 12.1

“DC Characteristics: PIC16C712/716-04 (Commercial, Industrial,

Extended) PIC16C712/716-20 (Commercial, Industrial,

Extended)” and Section 12.2 “DC Characteristics: PIC16LC712/

716-04 (Commercial, Industrial)”

Param

No.

Sym.

Characteristic

Min.

Typ†

Max.

Units

Conditions

Input Low Voltage

VIL

I/O ports

D030

D030A

with TTL buffer

VSS

—

0.8V

0.15VDD

4.5V

 VDD  5.5V

otherwise

D031

with Schmitt Trigger buffer

VSS

—

0.2VDD

D032

MCLR, OSC1 (in RC mode)

Vss

—

0.2VDD

D033

OSC1 (in XT, HS and LP

modes)

Vss

—

0.3VDD

(Note 1)

Input High Voltage

VIH

I/O ports

—

D040

with TTL buffer

2.0

—

VDD

4.5V

 VDD  5.5V

D040A

0.25VDD

+ 0.8V

—

VDD

Votherwise

D041

with Schmitt Trigger buffer

0.8VDD

—

VDD

For entire VDD range

D042

MCLR

0.8VDD

—

VDD

D042A

OSC1 (XT, HS and LP modes)

0.7VDD

—

VDD

(Note 1)

D043

OSC1 (in RC mode)

0.9VDD

—

VDD

Input Leakage Current

(Notes 2, 3)

D060

IIL

I/O ports

——

1

AVss VPIN VDD,

Pin at high-impedance

D061

MCLR, RA4/T0CKI

——

5

AVss VPIN VDD

D063

OSC1

——

5

AVss VPIN VDD,

XT, HS and LP osc modes

D070

IPURB

PORTB weak pull-up current

250

400

A VDD = 5V, VPIN = VSS

These parameters are characterized but not tested.

†

Data in “Typ” column is at 5V, 25

C unless otherwise stated. These parameters are for design guidance only

and are not tested.

Note 1: In RC Oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC

MCU be driven with external clock in RC mode.

2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified

levels represent normal operating conditions. Higher leakage current may be measured at different input

voltages.

3: Negative current is defined as current sourced by the pin.

PIC16LC712 Datasheet(PDF) 77 Page - Microchip Technology

PIC16LC712 Datasheet(HTML) 77 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL