PIC16C72-04SLASHSS datasheet(99/288 Pages) MICROCHIP

99 / 288 page

DS30390E-page 99

PIC16C7X

12.0

UNIVERSAL SYNCHRONOUS

ASYNCHRONOUS RECEIVER

TRANSMITTER (USART)

The Universal Synchronous Asynchronous Receiver

Transmitter (USART) module is one of the two serial

I/O modules. (USART is also known as a Serial Com-

munications Interface or SCI). The USART can be con-

ﬁgured as a full duplex asynchronous system that can

communicate with peripheral devices such as CRT ter-

minals and personal computers, or it can be conﬁgured

Applicable Devices

72 73 73A 74 74A 76 77

as a half duplex synchronous system that can commu-

nicate with peripheral devices such as A/D or D/A inte-

grated circuits, Serial EEPROMs etc.

The USART can be conﬁgured in the following modes:

• Asynchronous (full duplex)

• Synchronous - Master (half duplex)

• Synchronous - Slave (half duplex)

Bit SPEN (RCSTA<7>), and bits TRISC<7:6>, have to

be set in order to conﬁgure pins RC6/TX/CK and RC7/

RX/DT as the Universal Synchronous Asynchronous

Receiver Transmitter.

FIGURE 12-1: TXSTA: TRANSMIT STATUS AND CONTROL REGISTER (ADDRESS 98h)

R/W-0

U-0

R/W-0

R-1

R/W-0

CSRC

TX9

TXEN

SYNC

—

BRGH

TRMT

TX9D

R = Readable bit

W = Writable bit

U = Unimplemented bit,

read as ‘0’

- n =Value at POR reset

bit7

bit0

bit 7:

CSRC: Clock Source Select bit

Asynchronous mode

Don’t care

Synchronous mode

1 = Master mode (Clock generated internally from BRG)

0 = Slave mode (Clock from external source)

bit 6:

TX9: 9-bit Transmit Enable bit

1 = Selects 9-bit transmission

0 = Selects 8-bit transmission

bit 5:

TXEN: Transmit Enable bit

1 = Transmit enabled

0 = Transmit disabled

Note: SREN/CREN overrides TXEN in SYNC mode.

bit 4:

SYNC: USART Mode Select bit

1 = Synchronous mode

0 = Asynchronous mode

bit 3:

Unimplemented: Read as '0'

bit 2:

BRGH: High Baud Rate Select bit

Asynchronous mode

1 = High speed

Note:

For the PIC16C73/73A/74/74A, the asynchronous high speed mode (BRGH = 1) may expe-

rience a high rate of receive errors. It is recommended that BRGH = 0. If you desire a higher

baud rate than BRGH = 0 can support, refer to the device errata for additional information,

or use the PIC16C76/77.

0 = Low speed

Synchronous mode

Unused in this mode

bit 1:

TRMT: Transmit Shift Register Status bit

1 = TSR empty

0 = TSR full

bit 0:

TX9D: 9th bit of transmit data. Can be parity bit.

PIC16C72-04/SS Datasheet(PDF) 99 Page - Microchip Technology

PIC16C72-04/SS Datasheet(HTML) 99 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL