TDA7412 datasheet(34/56 Pages) STMICROELECTRONICS

34 / 56 page

TDA7412

34/56

4.0 FUNCTIONAL DESCRIPTION OF THE NOISEBLANKER

In the automotive environment the MPX-signal as well as the AM-signal is disturbed by spikes produced by the

ignition and other radiating sources like the wiper-motor. The aim of the noiseblanker part is to cancel the audi-

ble influence of the spikes. Therefore the output of the stereodecoder is held at the actual voltage for a time

between 22 and 38µs in FM (370 and 645µs in AM-mode). The blockdiagram of the noiseblanker is given in

fig.31.

Figure 29. Block diagram of the noiseblanker

In a first stage the spikes must be detected but to avoid a wrong triggering on high frequency (white) noise a

complex trigger control is implemented. Behind the triggerstage a pulse former generates the "blanking"-pulse.

4.1 Trigger Path FM

The incoming MPX signal is highpass-filtered, amplified and rectified. This second order highpass-filter has a

corner-frequency of 140kHz. The rectified signal, RECT, is integrated (lowpass filtered) to generate a signal

called PEAK. The DC-charge/discharge behaviour can be adjusted as well as the transient behaviour(MP-dis-

charge control). Also noise with a frequency 140kHz increases the PEAK voltage. The PEAK voltage is fed to

a threshold generator, which adds to the PEAK-voltage a DC-dependent threshold VTH. Both signals, RECT

and PEAK+VTH are fed to a comparator which triggers a re-triggerable monoflop. The monoflop's output acti-

vates the sample-and-hold circuits in the signalpath for the selected duration.

4.2 Noise Controlled Threshold Adjustment (NCT)

There are mainly two independent possibilities for programming the trigger threshold:

1. the low threshold in 8 steps (bits D1 to D3 of the noiseblanker-byte I)

2. and the noise adjusted threshold in 4 steps (bits D4 and D5 of the noiseblanker-byte I, see fig. 19).

The low threshold is activ in combination with a good MPX signal without noise; the PEAK voltage is less than

1V. The sensitivity in this operation is high.

If the MPX signal is noisy (low fieldstrength) the PEAK voltage increases due to the higher noise, which is also

rectified. With increasing of the PEAK voltage the trigger threshold increases, too. This gain is programmable

in 4 steps (see fig. 22).

4.3 Additional Threshold Control Mechanism

4.3.1 Automatic Threshold Control by the Stereoblend voltage

Besides the noise controlled threshold adjustment there is an additional possibility for influencing the trigger

threshold which depends on the stereoblend control.

The point where the MPX signal starts to become noisy is fixed by the RF part. Therefore also the starting point

RECTIFIER

AM/FM

INTEGRATOR

DISCHARGE

CONTROL

FM: 22 to 40

µs

AM: 370 to 6400

µs

RECT

THRESHOLD

GENERATOR

VTH

PEAK

ADDITIONAL

THRESHOLD

CONTROL

MONOFLOP

HOLDN

AMIF

D00AU1132

RECTIFIER +

14-56KHz LPF

(1st. order)

140KHz HPF

(1st. order)

140KHz HPF

(2nd. order)

MPX

MPOUT

TDA7412 Datasheet(PDF) 34 Page - STMicroelectronics

TDA7412 Datasheet(HTML) 34 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

Datasheet Download

Link URL