PIC16F818-ESLASHML datasheet(89/176 Pages) MICROCHIP

89 / 176 page

 2003 Microchip Technology Inc.

DS39598D-page 87

PIC16F818/819

11.5

A/D Operation During Sleep

The A/D module can operate during Sleep mode. This

requires that the A/D clock source be set to RC

(ADCS1:ADCS0 = 11). When the RC clock source is

selected, the A/D module waits one instruction cycle

before starting the conversion. This allows the SLEEP

instruction to be executed which eliminates all digital

switching noise from the conversion. When the conver-

sion is completed, the GO/DONE bit will be cleared and

the result loaded into the ADRES register. If the A/D

interrupt is enabled, the device will wake-up from

Sleep. If the A/D interrupt is not enabled, the A/D

module will then be turned off, although the ADON bit

will remain set.

When the A/D clock source is another clock option (not

RC), a SLEEP instruction will cause the present conver-

sion to be aborted and the A/D module to be turned off,

though the ADON bit will remain set.

Turning off the A/D places the A/D module in its lowest

current consumption state.

11.6

Effects of a Reset

A device Reset forces all registers to their Reset state.

The A/D module is disabled and any conversion in

progress is aborted. All A/D input pins are configured

as analog inputs.

The value that is in the ADRESH:ADRESL registers

not

modified

for

Power-on

Reset.

The

ADRESH:ADRESL registers will contain unknown data

after a Power-on Reset.

11.7

Use of the CCP Trigger

An A/D conversion can be started by the “special event

trigger” of the CCP module. This requires that the

CCP1M3:CCP1M0

bits

(CCP1CON<3:0>)

programmed as ‘1011’ and that the A/D module is

enabled (ADON bit is set). When the trigger occurs, the

GO/DONE bit will be set, starting the A/D conversion

and the Timer1 counter will be reset to zero. Timer1 is

reset to automatically repeat the A/D acquisition period

with

minimal

software

overhead

(moving

the

ADRESH:ADRESL to the desired location). The appro-

priate analog input channel must be selected and the

minimum acquisition done before the “special event

trigger” sets the GO/DONE bit (starts a conversion).

If the A/D module is not enabled (ADON is cleared),

then the “special event trigger” will be ignored by the

A/D module but will still reset the Timer1 counter.

TABLE 11-2:

REGISTERS/BITS ASSOCIATED WITH A/D

Note:

For the A/D module to operate in Sleep,

the A/D clock source must be set to RC

(ADCS1:ADCS0 = 11). To perform an A/D

conversion in Sleep, ensure the SLEEP

instruction

immediately

follows

the

instruction that sets the GO/DONE bit.

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Value on

POR, BOR

Value on

all other

Resets

0Bh,8Bh

10Bh,18Bh

INTCON

GIE

PEIE

TMR0IE

INTE

RBIE

TMR0IF

INTF

RBIF

0000 000x

0000 000u

0Ch

PIR1

—ADIF

—

SSPIF

CCP1IF

TMR2IF TMR1IF

-0-- 0000

8Ch

PIE1

—ADIE

—

SSPIE

CCP1IE

TMR2IE TMR1IE -0-- 0000

-0-- 0000

1Eh

ADRESH

A/D Result Register High Byte

xxxx xxxx

uuuu uuuu

9Eh

ADRESL

A/D Result Register Low Byte

xxxx xxxx

uuuu uuuu

1Fh

ADCON0

ADCS1 ADCS0

CHS2

CHS1

CHS0

GO/DONE

—ADON

0000 00-0

9Fh

ADCON1

ADFM

ADCS2

—

PCFG3

PCFG2

PCFG1

PCFG0

00-- 0000

05h

PORTA

RA7

RA6

RA5

RA4

RA3

RA2

RA1

RA0

xxx0 0000

uuu0 0000

85h

TRISA

TRISA7 TRISA6 TRISA5 PORTA Data Direction Register

1111 1111

Legend:

= unknown, u = unchanged, - = unimplemented, read as ‘0’. Shaded cells are not used for A/D conversion.

PIC16F818-E/ML Datasheet(PDF) 89 Page - Microchip Technology

PIC16F818-E/ML Datasheet(HTML) 89 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL