PIC16F818-ESLASHML datasheet(131/176 Pages) MICROCHIP

131 / 176 page

 2004 Microchip Technology Inc.

DS39598E-page 129

PIC16F818/819

VOL

Output Low Voltage

D080

I/O ports

—

0.6

IOL = 8.5 mA, VDD = 4.5V,

-40

°C to +125°C

D083

OSC2/CLKO

(RC oscillator config)

——

0.6

IOL = 1.6 mA, VDD = 4.5V,

-40

°C to +125°C

VOH

Output High Voltage

D090

I/O ports (Note 3)

VDD – 0.7

—

IOH = -3.0 mA, VDD = 4.5V,

-40

°C to +125°C

D092

OSC2/CLKO

(RC oscillator config)

VDD – 0.7

—

IOH = -1.3 mA, VDD = 4.5V,

-40

°C to +125°C

Capacitive Loading Specs on Output Pins

D100

COSC2 OSC2 pin

—

In XT, HS and LP modes

when external clock is used

to drive OSC1

D101

CIO

All I/O pins and OSC2

(in RC mode)

—

D102

SCL, SDA in I2C™ mode

——

400

Data EEPROM Memory

D120

Endurance

100K

10K

100K

—

E/W

-40°C to +85°C

+85°C to +125°C

D121

VDRW VDD for read/write

VMIN

—

5.5

Using EECON to read/write,

VMIN = min. operating

voltage

D122

TDEW Erase/write cycle time

—

Program Flash Memory

D130

Endurance

10K

100K

10K

—

E/W

-40°C to +85°C

+85°C to +125°C

D131

VPR

VDD for read

VMIN

—5.5

D132A

VDD for erase/write

VMIN

—

5.5

Using EECON to read/write,

VMIN = min. operating

voltage

D133

TPE

Erase cycle time

—

D134

TPW

Write cycle time

—

15.4

DC Characteristics:

PIC16F818/819 (Industrial, Extended)

PIC16LF818/819 (Industrial) (Continued)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C

≤ TA ≤ +85°C for industrial

-40°C

≤ TA ≤ +125°C for extended

Operating voltage VDD range as described in Section 15.1 “DC

Characteristics: Supply Voltage”.

Param

No.

Sym

Characteristic

Min

Typ†

Max

Units

Conditions

† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance

only and are not tested.

Note 1:

In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the

PIC16F818/819 be driven with external clock in RC mode.

The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels

represent normal operating conditions. Higher leakage current may be measured at different input voltages.

Negative current is defined as current sourced by the pin.

PIC16F818-E/ML Datasheet(PDF) 131 Page - Microchip Technology

PIC16F818-E/ML Datasheet(HTML) 131 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL