56F8167 datasheet(115/184 Pages) FREESCALE

115 / 184 page

56F8367 Technical Data, Rev. 7.0

Freescale Semiconductor

115

Preliminary

6.5.1.2

EMI_MODE (EMI_MODE)—Bit 6

This bit reflects the current (non-clocked) state of the EMI_MODE pin. During reset, this bit, coupled with

the EXTBOOT signal, is used to initialize address bits [19:16] either as GPIO or as address. These settings

can be explicitly overwritten using the appropriate GPIO peripheral enable register at any time after reset.

In addition, this pin can be used as a general purpose input pin after reset.

•

0 = External address bits [19:16] are initially programmed as GPIO

•

1 = When booted with EXTBOOT = 1, A[19:16] are initially programmed as address. If EXTBOOT is 0,

they are initialized as GPIO.

6.5.1.3

OnCE Enable (OnCE EBL)—Bit 5

•

0 = OnCE clock to 56800E core enabled when core TAP is enabled

•

1 = OnCE clock to 56800E core is always enabled

6.5.1.4

Software Reset (SW RST)—Bit 4

This bit is always read as 0. Writing a 1 to this bit will cause the part to reset.

6.5.1.5

Stop Disable (STOP_DISABLE)—Bits 3–2

•

00 - Stop mode will be entered when the 56800E core executes a STOP instruction

•

01 - The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can be

reprogrammed in the future

•

10 - The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can then only be

changed by resetting the device

•

11 - Same operation as 10

6.5.1.6

Wait Disable (WAIT_DISABLE)—Bits 1–0

•

00 - Wait mode will be entered when the 56800E core executes a WAIT instruction

•

01 - The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can be

reprogrammed in the future

•

10 - The HawkV2 WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can then only

be changed by resetting the device

•

11 - Same operation as 10

6.5.2

SIM Reset Status Register (SIM_RSTSTS)

Bits in this register are set upon any system reset and are initialized only by a Power-On Reset (POR). A

reset (other than POR) will only set bits in the register; bits are not cleared. Only software should clear this

Figure 6-4 SIM Reset Status Register (SIM_RSTSTS)

Base + $1

Read

SWR

COPR

EXTR

POR

Write

RESET

56F8167 Datasheet(PDF) 115 Page - Freescale Semiconductor, Inc

56F8167 Datasheet(HTML) 115 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL