| Electronic Components Datasheet Search |
|
S25FL040A0LMAI011 Datasheet(PDF) 26 Page - SPANSION |
|
|
|||||||||||||||||||||||||||||
S25FL040A0LMAI011 Datasheet(HTML) 26 Page - SPANSION |
|
26 / 35 page ![]() 24 S25FL040A S25FL040A_00_B0 August 31, 2006 Data Sheet (Pre limin ar y) When CS# is driven high, the device transitions from DP mode to the standby mode after a delay of tRES, as previously described. The RES command always provides access to the Electronic Signature of the device and can be applied even if DP mode has not been entered. Any RES command issued while an erase, program, or WRSR operation is in progress not executed, and the operation continues uninterrupted. Figure 9.14 Release from Deep Power Down and Read Electronic Signature (RES) Command Sequence Notes 1. The S25FL040A has a manufacturer ID of 01h, and a device ID consisting of the memory type (02h) and the memory capacity (12h for uniform sector, 25h for top boot, 26h for bottom boot). 2. The S25FL040A has an Electronic Signature ID of 12h. 10. Power-up and Power-down During power-up and power-down, certain conditions must be observed. CS# must follow the voltage applied on VCC, and must not be driven low to select the device until VCC reaches the allowable values as follows (see Figure 10.1 and Table 10.1): At power-up, VCC (min) plus a period of tPU At power-down, VSS CS# SCK SI SO 3 Dummy Bytes Hi-Z MSB Deep Power-down Mode Standby Mode 0 1 2 3 45 6 7 8 9 10 28 29 30 31 32 33 34 35 36 37 38 Electronic ID out Command tRES 23 22 21 3 2 10 7 65 4 3 2 1 0 MSB Table 9.5 Command Definitions Operation Command Description One-Byte Command Code Address Bytes Dummy Byte Data Bytes Read READ Read Data Bytes 03H (0000 0011) 3 0 1 to ∞ FAST_READ Read Data Bytes at Higher Speed 0BH (0000 1011) 3 1 1 to ∞ RDID Read Identification (Note 1) 9FH (1001 1111) 0 0 1 to 3 READ_ID Read Manufacture and Device Identification (Note 1) 90H (1001 0000) 3 0 1 to ∞ Write Control WREN Write Enable 06H (0000 0110) 0 0 0 WRDI Write Disable 04H (0000 0100) 0 0 0 Erase SE Sector Erase D8H (1101 1000) 3 0 0 BE Bulk (Chip) Erase C7H (1100 0111) 0 0 0 Program PP Page Program 02H (0000 0010) 3 0 1 to 256 Status Register RDSR Read from Status Register 05H (0000 0101) 0 0 1 to ∞ WRSR Write to Status Register 01H (0000 0001) 0 0 1 Power Saving DP Deep Power Down B9H (1011 1001) 0 0 0 RES Release from Deep Power Down ABH (1010 1011) 0 0 0 Release from Deep Power Down and Read Electronic Signature (Note 2) ABH (1010 1011) 0 3 1 to ∞ |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |