Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

S25FL040A0LMAI011 Datasheet(PDF) 21 Page - SPANSION

Part # S25FL040A0LMAI011
Description  4 Megabit CMOS 3.0 Volt Flash Memory with 50MHz SPI (Serial Peripheral Interface) Bus and Small Sector for Boot and Parameter Storage
PDF  35 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  SPANSION [SPANSION]
Direct Link  http://www.spansion.com
Logo SPANSION - SPANSION

S25FL040A0LMAI011 Datasheet(HTML) 21 Page - SPANSION

Back Button S25FL040A0LMAI011 Datasheet HTML 17Page - SPANSION S25FL040A0LMAI011 Datasheet HTML 18Page - SPANSION S25FL040A0LMAI011 Datasheet HTML 19Page - SPANSION S25FL040A0LMAI011 Datasheet HTML 20Page - SPANSION S25FL040A0LMAI011 Datasheet HTML 21Page - SPANSION S25FL040A0LMAI011 Datasheet HTML 22Page - SPANSION S25FL040A0LMAI011 Datasheet HTML 23Page - SPANSION S25FL040A0LMAI011 Datasheet HTML 24Page - SPANSION S25FL040A0LMAI011 Datasheet HTML 25Page - SPANSION Next Button
Zoom Inzoom in Zoom Outzoom out
 21 / 35 page
background image
August 31, 2006 S25FL040A_00_B0
S25FL040A
19
Da ta
Shee t
(Prelim i nar y )
Figure 9.7 Read Status Register (RDSR) Command Sequence
The following describes the status and control bits of the Status Register.
Write In Progress (WIP) bit: Indicates whether the device is busy performing a Write Status Register,
program, or erase operation. This bit is read-only, and is controlled internally by the device. If WIP is 1, one of
these operations is in progress; if WIP is 0, no such operation is in progress.
Write Enable Latch (WEL) bit: Determines whether the device will accept and execute a Write Status
Register, program, or erase command. When set to 1, the device accepts these commands; when set to 0,
the device rejects the commands. This bit is set to 1 by writing the WREN command, and set to 0 by the
WRDI command, and is also automatically reset to 0 after the completion of a Write Status Register, program,
or erase operation. WEL cannot be directly set by the WRSR command.
Block Protect (BP2, BP1, BP0) bits: Define the portion of the memory area that will be protected against
any changes to the stored data. The Write Status Register (WRSR) command controls these bits, which are
non-volatile. When one or more of these bits is set to 1, the corresponding memory area (see Table 7.1 on
page 11) is protected against Page Program (PP) and Sector Erase (SE) commands. If the Hardware
Protected mode is enabled, BP2:BP0 cannot be changed. The Bulk Erase (BE) command is executed only if
all Block Protect (BP2, BP1, BP0) bits are 0.
Status Register Write Disable (SRWD) bit: Provides data protection when used together with the Write
Protect (W#) signal. When SRWD is set to 1 and W# is driven low, the device enters the Hardware Protected
mode. The non-volatile bits of the Status Register (SRWD, BP2, BP1, BP0) become read-only bits and the
device ignores any Write Status Register (WRSR) command.
9.8
Write Status Register (WRSR)
The Write Status Register (WRSR) command changes the bits in the Status Register. A Write Enable
(WREN) command, which itself sets the Write Enable Latch (WEL) in the Status Register, is required prior to
writing the WRSR command. Table 9.3, S25FL040A Status Register on page 18 shows the status register
bits and their functions.
The host system must drive CS# low, write the WRSR command, and the appropriate data byte on SI
(Figure 9.8).
The WRSR command cannot change the state of the Write Enable Latch (bit 1). The WREN command must
be used for that purpose. Bit 0 is a status bit controlled internally by the Flash device. Bits 6 and 5 are always
read as 0 and have no user significance.
The WRSR command also controls the value of the Status Register Write Disable (SRWD) bit. The SRWD bit
and W# together place the device in the Hardware Protected Mode (HPM). The device ignores all WRSR
commands once it enters the Hardware Protected Mode (HPM). Table 9.4 shows that W# must be driven low
and the SRWD bit must be 1 for this to occur.
Command
Hi-Z
MSB
MSB
Status Register Out
Status Register Out
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
7 6
5 4
3
2
10 7
6
5 4
3
2
1 0 7
SO
SI
SCK
CS#
Mode 3
Mode 0



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com