| Electronic Components Datasheet Search |
|
C8051F53X Datasheet(PDF) 41 Page - Silicon Laboratories |
|
|
|||||||||||||||||||||||||||||
C8051F53X Datasheet(HTML) 41 Page - Silicon Laboratories |
|
41 / 220 page ![]() Rev. 0.3 41 C8051F52x-53x 5. 12-Bit ADC (ADC0) The ADC0 subsystem for the C8051F52x/F53x Family consists of an analog multiplexer (AMUX0) with 16/6 total input selections, and a 200 ksps, 12-bit successive-approximation-register ADC with integrated track-and-hold, programmable window detector, programmable attenuation (1:2), and hardware accumula- tor. The ADC0 subsystem has a special Burst Mode which can automatically enable ADC0, capture and accumulate samples, then place ADC0 in a low power shutdown mode without CPU intervention. The AMUX0, data conversion modes, and window detector are all configurable under software control via the Special Function Registers shown in Figure 5.1. ADC0 inputs are single-ended and may be configured to measure P0.0-P2.7, the Temperature Sensor output, VDD, or GND with respect to GND. ADC0 is enabled when the AD0EN bit in the ADC0 Control register (ADC0CN) is set to logic 1, or when performing conver- sions in Burst Mode. ADC0 is in low power shutdown when AD0EN is logic 0 and no Burst Mode conver- sions are taking place. 12-Bit SAR ADC 32 ADC0CN Start Conversion VDD ADC0LTH AD0WINT 19-to-1 AMUX0 VDD P0.0 P0.7 Window Compare Logic P1.0* P1.7* ADC0LTL ADC0GTH ADC0GTL ADC0MX GND Temp Sensor ADC0CF ADC0TK Burst Mode Logic Accumulator Start Conversion Burst Mode Oscillator 25 MHz Max SYSCLK *Available in ‘F53x devices 00 AD0BUSY (W) 10 CNVSTR Input Timer 2 Overflow 11 01 Timer 1 Overflow Figure 5.1. ADC0 Functional Block Diagram 5.1. Analog Multiplexer AMUX0 selects the input channel to the ADC. Any of the following may be selected as an input: P0.0– P1.7, the on-chip temperature sensor, the core power supply (VDD), or ground (GND). ADC0 is single- ended and all signals measured are with respect to GND. The ADC0 input channels are selected using the ADC0MX register as described in SFR Definition 5.1. Important Note About ADC0 Input Configuration: Port pins selected as ADC0 inputs should be config- ured as analog inputs, and should be skipped by the Digital Crossbar. To configure a Port pin for analog input, set to ‘0’ the corresponding bit in register PnMDIN (for n = 0,1). To force the Crossbar to skip a Port pin, set to ‘1’ the corresponding bit in register PnSKIP (for n = 0,1). See Section “14. Port Input/Output” on page 117 for more Port I/O configuration details. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |