Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

LMH2191TMX/NOPB Datasheet(PDF) 12 Page - Texas Instruments

Part # LMH2191TMX/NOPB
Description  LMH2191 Dual Channel 52 MHz Clock Tree Driver
PDF  22 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI2 [Texas Instruments]
Direct Link  https://www.ti.com
Logo TI2 - Texas Instruments

LMH2191TMX/NOPB Datasheet(HTML) 12 Page - Texas Instruments

Back Button LMH2191TMX/NOPB Datasheet HTML 8Page - Texas Instruments LMH2191TMX/NOPB Datasheet HTML 9Page - Texas Instruments LMH2191TMX/NOPB Datasheet HTML 10Page - Texas Instruments LMH2191TMX/NOPB Datasheet HTML 11Page - Texas Instruments LMH2191TMX/NOPB Datasheet HTML 12Page - Texas Instruments LMH2191TMX/NOPB Datasheet HTML 13Page - Texas Instruments LMH2191TMX/NOPB Datasheet HTML 14Page - Texas Instruments LMH2191TMX/NOPB Datasheet HTML 15Page - Texas Instruments LMH2191TMX/NOPB Datasheet HTML 16Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 12 / 22 page
background image
Duty Cycle 50%
Duty Cycle 50%
Shifted DC level
DC level 50% duty cycle
SCLK_IN
CSERIES
LMH2191
SNAS485D – JULY 2010 – REVISED MAY 2013
www.ti.com
Due to the internal coupling capacitor, the clock signal is DC biased, since the coupling capacitor prevents the
internal biasing of the input circuitry to be affected by the external DC voltage. Because of the coupling capacitor,
the minimum clock frequency is 10 MHz. It is assumed that the input signal is a sine wave or a typical TCXO
waveform (the signal from a TCXO has slow edges), enabling the control loop to adjust to a duty cycle of 50% if
the input signal differs slightly from 50% duty cycle. The duty cycle is an important timing parameter for the
peripheral equipment. The circuit that adjust the duty cycle is shown in Figure 19.
Figure 19. Clock Duty Cycle Regulation
Figure 20. Duty Cycle adjust levels
|n order to achieve a duty cycle of 50%, the edges of the incoming clock signal (SCLK_IN) are used to move the
switching point to the level that is needed to create the 50% duty cycle. The simplified input circuit consists of an
inverter and a feedback resistor. Together with the input series capacitor of about 30 pF, the circuit creates a DC
level depending on the duty cycle of the incoming clock signal. When the duty cycle is exactly 50%, the DC level
is in the middle of the upper and lower pulse level. When the duty cycle differs from 50%, the DC level shifts
slightly to maintain the duty cycle level at 50%. (See Duty Cycle adjust levels of Figure 20.) As explained above,
the slow edges of the SCLK_IN signal are important to make the control loop work.
Input Impedance
The input impedance can be split up into two parts: the DC input resistance and the AC input impedance. Due to
the used series capacitor in the input signal path the DC resistance is infinite. The AC input impedance is formed
by the circuit drawn in Figure 19. This circuit consists of an inverter and a feedback resistor. A signal fed to the
input pin is connected to the inverter input which has a high input impedance and is in parallel to the feedback
resistor of 30 k
Ω. The other pin of the feedback resistor is connected to the output of the inverter which means
that the input current is higher than it would be if it were connected to a decoupled supply connection. For this
reason the AC input resistance can be much lower than the connected feedback resistor of 30 k
Ω. The input
resistance is dependant on the amplitude of the input signal. When an input amplitude of 1.8V is used (the same
amplitude as the output of the inverter), the input impedance is theoretical half the value of the feedback resistor.
When the amplitude of the input signal lowers, the input resistance becomes lower too. With an input signal of
1VPP, the input impedance will be about 10 kΩ.
Clock Tree Driver Outputs
The LMH2191's clock tree driver outputs have a drive strength that make each output capable of driving a
capacitive load up to 50 pF, together with a minimum of EMI. Further reduction of EMI is achieved by the
inversion of the CLK2 output. (See Figure 21.) Both the drive strength and the capacitive load make the edges of
the output pulse relative slow which is favorable for EMI reduction.
12
Submit Documentation Feedback
Copyright © 2010–2013, Texas Instruments Incorporated
Product Folder Links: LMH2191



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com