S5D3 datasheet(13/89 Pages) RENESAS

13 / 89 page

R01DS0328EU0120 Rev.1.20

Page 13 of 89

Dec 13, 2023

S5D3 Datasheet

1. Overview

SPI

RSPCKA, RSPCKB

I/O

Clock input/output pin

MOSIA, MOSIB

I/O

Input or output pins for data output from the master

MISOA, MISOB

I/O

Input or output pins for data output from the slave

SSLA0, SSLB0

I/O

Input or output pin for slave selection

SSLA1 to SSLA3,

SSLB1 to SSLB3

Output

Output pins for slave selection

QSPI

QSPCLK

Output

QSPI clock output pin

QSSL

Output

QSPI slave output pin

QIO0 to QIO3

I/O

Data0 to Data3

CAN

CRX0, CRX1

Input

Receive data

CTX0, CTX1

Output

Transmit data

USBFS

VCC_USB

Input

Power supply pins

VSS_USB

Input

Ground pins

USB_DP

I/O

D+ I/O pin of the USB on-chip transceiver. Connect this pin to the D+ pin of

the USB bus

USB_DM

I/O

D- I/O pin of the USB on-chip transceiver. Connect this pin to the D- pin of

the USB bus

USB_VBUS

Input

USB cable connection monitor pin. Connect this pin to VBUS of the USB

bus. The VBUS pin status (connected or disconnected) can be detected

when the USB module is operating as a device controller.

USB_EXICEN

Output

Low-power control signal for external power supply (OTG) chip

USB_VBUSEN

Output

VBUS (5 V) supply enable signal for external power supply chip

USB_OVRCURA,

USB_OVRCURB

Input

Connect the external overcurrent detection signals to these pins. Connect

the VBUS comparator signals to these pins when the OTG power supply

chip is connected.

USB_ID

Input

Connect the MicroAB connector ID input signal to this pin during operation in

OTG mode

SDHI

SD0CLK, SD1CLK

Output

SD clock output pins

SD0CMD, SD1CMD

I/O

Command output pin and response input signal pins

SD0DAT0 to

SD0DAT3,

SD1DAT0 to

SD1DAT3

I/O

SD and MMC data bus pins

SD0CD

Input

SD card detection pins

SD0WP

Input

SD write-protect signals

Analog power

supply

AVCC0

Input

Analog voltage supply pin. This is used as the analog power supply for the

respective modules. Supply this pin with the same voltage as the VCC pin.

AVSS0

Input

Analog ground pin. This is used as the analog ground for the respective

modules. Supply this pin with the same voltage as the VSS pin.

VREFH0

Input

Analog reference voltage supply pin for the ADC12 (unit 0). Connect this pin

to VCC when not using the ADC12 (unit 0) and sample-and-hold circuit for

AN000 to AN002.

VREFL0

Input

Analog reference ground pin for the ADC12. Connect this pin to VSS when

not using the ADC12 (unit 0) and sample-and-hold circuit for AN000 to

AN002

VREFH

Input

Analog reference voltage supply pin for the ADC12 (unit 1) and D/A

Converter. Connect this pin to VCC when not using the ADC12 (unit 1),

sample-and-hold circuit for AN100 to AN102, and D/A Converter.

VREFL

Input

Analog reference ground pin for the ADC12 and D/A Converter. Connect this

pin to VSS when not using the ADC12 (unit 1), sample-and-hold circuit for

AN100 to AN102, and D/A Converter.

Table 1.16

Pin functions (3 of 4)

Function

Signal

I/O

Description

S5D3 Datasheet(PDF) 13 Page - Renesas Technology Corp

S5D3 Datasheet(HTML) 13 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89

Datasheet Download

Link URL