NRF52810-QFAA-R datasheet(188/483 Pages) NORDIC

188 / 483 page

Peripherals

Symbol

Description

Min.

Typ.

Max.

Units

VIL

Input low voltage

VSS

0.3 x

VDD

VOH,SD

Output high voltage, standard drive, 0.5 mA, VDD ≥1.7

VDD-0.4

VDD

VOH,HDH

Output high voltage, high drive, 5 mA, VDD >= 2.7 V

VDD-0.4

VDD

VOH,HDL

Output high voltage, high drive, 3 mA, VDD >= 1.7 V

VDD-0.4

VDD

VOL,SD

Output low voltage, standard drive, 0.5 mA, VDD ≥1.7

VSS

VSS+0.4 V

VOL,HDH

Output low voltage, high drive, 5 mA, VDD >= 2.7 V

VSS

VSS+0.4 V

VOL,HDL

Output low voltage, high drive, 3 mA, VDD >= 1.7 V

VSS

VSS+0.4 V

IOL,SD

Current at VSS+0.4 V, output set low, standard drive, VDD

≥1.7

IOL,HDH

Current at VSS+0.4 V, output set low, high drive, VDD >= 2.7

IOL,HDL

Current at VSS+0.4 V, output set low, high drive, VDD >= 1.7

IOH,SD

Current at VDD-0.4 V, output set high, standard drive, VDD

≥1.7

IOH,HDH

Current at VDD-0.4 V, output set high, high drive, VDD >= 2.7

IOH,HDL

Current at VDD-0.4 V, output set high, high drive, VDD >= 1.7

tRF,15pF

Rise/fall time, standard drive mode, 10-90%, 15 pF load1

tRF,25pF

Rise/fall time, standard drive mode, 10-90%, 25 pF load1

tRF,50pF

Rise/fall time, standard drive mode, 10-90%, 50 pF load1

tHRF,15pF

Rise/Fall time, high drive mode, 10-90%, 15 pF load1

tHRF,25pF

Rise/Fall time, high drive mode, 10-90%, 25 pF load1

tHRF,50pF

Rise/Fall time, high drive mode, 10-90%, 50 pF load1

RPU

Pull-up resistance

kΩ

RPD

Pull-down resistance

kΩ

CPAD

Pad capacitance

6.9 GPIOTE — GPIO tasks and events

The GPIO tasks and events (GPIOTE) module provides functionality for accessing GPIO pins using tasks and

events. Each GPIOTE channel can be assigned to one pin.

A GPIOTE block enables GPIOs to generate events on pin state change which can be used to carry out tasks

through the PPI system. A GPIO can also be driven to change state on system events using the PPI system.

Low power detection of pin state changes is possible when in System ON or System OFF.

Instance

Number of GPIOTE channels

GPIOTE

Table 38: GPIOTE properties

Up to three tasks can be used in each GPIOTE channel for performing write operations to a pin. Two tasks

are fixed (SET and CLR), and one (OUT) is configurable to perform following operations:

• Set

• Clear

• Toggle

1 Rise and fall times based on simulations

4430_161 v1.0

188

NRF52810-QFAA-R Datasheet(PDF) 188 Page - Nordic Semiconductor

NRF52810-QFAA-R Datasheet(HTML) 188 Page - Nordic Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL