M32CSLASH86T datasheet(211/505 Pages) RENESAS

211 / 505 page

Page 188

17. Serial I/O

)

(

UARTi Transmit/Receive Control Register 1 (i=0 to 4)

Symbol

Address

After Reset

U0C1 to U4C1

036D16, 02ED16, 033D16, 032D16, 02FD16

0000 00102

UiIRS

UiRRM

UiLCH

Transmit

Enable Bit

Transmit Buffer

Empty Flag

Receive

Enable Bit

Receive

Complete Flag

Clock-Divided

Synchronous Stop

Bit /

Error Signal

Output Enable

Bit(1)

SCLKSTPB

/UiERE

UARTi Transmit

Interrupt Cause

Select Bit

UARTi

Continuous

Receive Mode

Enable Bit

Data Logic

Select Bit(2)

0: Transmit disable

1: Transmit enable

0: Data in the UiTB register

1: No data in the UiTB register

0: Receive disable

1: Receive enable

0: No data in the UiRB register

1: Data in the UiRB register

0: No data in the UiTB register (TI = 1)

1: Transmission is completed (TXEPT = 1)

0: Disables continuous receive mode to be entered

1: Enables continuous receive mode to be entered

0: Not inversed

1: Inverse

Clock-divided synchronous stop bit (special mode 3)

0: Stops synchronizing

1: Starts synchronizing

Error signal output enable bit (special mode 5)

0: Not output

1: Output

Bit Name

Bit

Symbol

Function

NOTES:

1. Set the SCLKSTPB/UiERE bit after setting the SMD2 to SMD0 bits in the UiMR register.

2. The UiLCH bit setting is enabled when setting the SMD2 to SMD0 bits to "0012" (clock syncronous

serial I/O mode), "1002" (UART mode, 7-bit transfer data) or "1012" (UART mode, 8-bit transfer data).

Set the UiLCH bit to "0" when setting the SMD2 to SMD0 bits to"0102" (I2C mode) or "1102" (UART

mode, 9-bit transfer data).

UARTi Special Mode Register (i=0 to 4)

Symbol

Address

After Reset

U0SMR to U4SMR

036716, 02E716, 033716, 032716, 02F716

0016

LSYN

ABSCS

ACSE

SSS

IICM

BBS

ABC

0: Except I2C mode

1: I2C mode

0: Update per bit

1: Update per byte

0: Stop condition detected

1: Start condition detected (Busy)

0: Disabled

1: Enabled

0: Not related to RxDi

1: Synchronized with RxDi

0: Rising edge of transfer clock

1: Timer Aj underflow(j=0 to 4)(2)

Bit Name

Bit

Symbol

I2C Mode Select Bit

Bus Busy Flag

NOTES:

1. The BBS bit is set to "0" by program. It is unchanged if set to "1".

2. UART0: timer A3 underflow signal, UART1: timer A4 underflow signal,

UART2: timer A0 underflow signal, UART3: timer A3 underflow signal,

UART4: timer A4 underflow signal.

3. Refer to notes for the SU1HIM bit in the UiSMR2 register.

Auto Clear Function Select

Bit for Transmit Enable Bit

SCLL Sync Output

Enable Bit

Arbitration Lost Detect

Flag Control Bit

Bus Conflict Detect

Sampling Clock Select Bit

Transmit Start

Condition Select Bit

0: No auto clear function

1: Auto clear at bus conflict

SCLKDIV

Clock Divide

Synchronous Bit

(Note 3)

RW(1)

Function

Figure 17.5 U0C1 to U4C1 Registers and U0SMR to U4SMR Registers

M32C/86T Datasheet(PDF) 211 Page - Renesas Technology Corp

M32C/86T Datasheet(HTML) 211 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL