| Electronic Components Datasheet Search |
|
3724MPFE Datasheet(PDF) 15 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
3724MPFE Datasheet(HTML) 15 Page - Linear Technology |
|
15 / 24 page ![]() LT3724 15 3724fc APPLICATIONS INFORMATION The VFB pin input bias current is typically 25nA, so use of extremely high value feedback resistors could cause a converter output that is slightly higher than expected. Bias current error at the output can be estimated as: ΔVOUT(BIAS) = 25nA • R2 Supply UVLO and Shutdown The SHDN pin has a precision voltage threshold with hysteresis which can be used as an undervoltage lockout threshold (UVLO) for the power supply. Undervoltage lockout keeps the LT3724 in shutdown until the supply input voltage is above a certain voltage programmed by the user. The hysteresis voltage prevents noise from falsely tripping UVLO. Resistors are chosen by first selecting RB. Then RA =RB • VSUPPLY(ON) 1.35V –1 VSUPPLY(ON) is the input voltage at which the undervoltage lockout is disabled and the supply turns on. Example: Select RB = 49.9kΩ, VSUPPLY(ON) = 14.5V (based on a 15V minimum input voltage) RA = 49.9k • 14.5V 1.35V –1 = 486.1kΩ (499kΩ resistor is selected) If low supply current in standby mode is required, select a higher value of RB. The supply turn off voltage is 9% below turn on. In the example the VSUPPLY(OFF) would be 13.2V. If additional hysteresis is desired for the enable function, an external positive feedback resistor can be used from the LT3724 regulator output. The shutdown function can be disabled by connecting the SHDN pin to the VIN through a large value pull-up resistor. This pin contains a low impedance clamp at 6V, so the SHDN pin will sink current from the pull-up resistor(RPU): I SHDN= VIN –6V RPU Because this arrangement will clamp the SHDN pin to the 6V, it will violate the 5V absolute maximum voltage rating of the pin. This is permitted, however, as long as the absolute maximum input current rating of 1mA is not exceeded. Input SHDN pin currents of <100μA are recommended: a 1MΩ or greater pull-up resistor is typically used for this configuration. Soft-Start The soft-start function forces the programmed slew rate while the converter output rises to 95% of regulation, which corresponds to 1.185V on the VFB pin. Once 95% regulation is achieved, the soft-start circuit is disabled. The soft-start circuit will re-enable when the VFB pin drops below 70% of regulation, which corresponds to 300mV of control hysteresis on the VFB pin. This allows for a controlled recovery from a “brown-out” condition. Figure 2. Output Voltage Feedback Divider Figure 3. Undervoltage Lockout Circuit L1 VFB PIN R2 R1 VOUT COUT 3724 F02 SHDN PIN RA RB VSUPPLY 3724 F03 Figure 4.Soft-Start Circuit RSS LT3724 VOUT CSS1 CSS 3724 F04 A |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |