PIC16F722-ESLASHML datasheet(102/302 Pages) MICROCHIP

102 / 302 page

PIC16F72X/PIC16LF72X

DS41341E-page 102

9.1.5

INTERRUPTS

The ADC module allows for the ability to generate an

interrupt upon completion of an Analog-to-Digital

conversion. The ADC interrupt flag is the ADIF bit in the

PIR1 register. The ADC interrupt enable is the ADIE bit

in the PIE1 register. The ADIF bit must be cleared in

software.

This interrupt can be generated while the device is

operating or while in Sleep. If the device is in Sleep, the

interrupt will wake-up the device. Upon waking from

Sleep, the next instruction following the SLEEP instruc-

tion is always executed. If the user is attempting to

wake-up from Sleep and resume in-line code execu-

tion, the GIE and PEIE bits of the INTCON register

must be disabled. If the GIE and PEIE bits of the INT-

CON register are enabled, execution will switch to the

Interrupt Service Routine.

Please refer to Section 9.1.5 “Interrupts” for more

information.

9.2

ADC Operation

9.2.1

STARTING A CONVERSION

To enable the ADC module, the ADON bit of the

ADCON0 register must be set to a ‘1’. Setting the GO/

DONE bit of the ADCON0 register to a ‘1’ will start the

Analog-to-Digital conversion.

9.2.2

COMPLETION OF A CONVERSION

When the conversion is complete, the ADC module will:

• Clear the GO/DONE bit

• Set the ADIF Interrupt Flag bit

• Update the ADRES register with new conversion

result

9.2.3

TERMINATING A CONVERSION

If a conversion must be terminated before completion,

the GO/DONE bit can be cleared in software. The

ADRES register will be updated with the partially com-

plete Analog-to-Digital conversion sample. Incomplete

bits will match the last bit converted.

9.2.4

ADC OPERATION DURING SLEEP

The ADC module can operate during Sleep. This

requires the ADC clock source to be set to the FRC

option. When the FRC clock source is selected, the

ADC waits one additional instruction before starting the

conversion. This allows the SLEEP instruction to be

executed, which can reduce system noise during the

conversion. If the ADC interrupt is enabled, the device

will

wake-up

from

Sleep

when

the

conversion

completes. If the ADC interrupt is disabled, the ADC

module is turned off after the conversion completes,

although the ADON bit remains set.

When the ADC clock source is something other than

FRC, a SLEEP instruction causes the present conver-

sion to be aborted and the ADC module is turned off,

although the ADON bit remains set.

9.2.5

SPECIAL EVENT TRIGGER

The Special Event Trigger of the CCP module allows

periodic ADC measurements without software inter-

vention. When this trigger occurs, the GO/DONE bit is

set by hardware and the Timer1 counter resets to zero.

Using the Special Event Trigger does not assure proper

ADC timing. It is the user’s responsibility to ensure that

the ADC timing requirements are met.

Refer

Section 15.0

“Capture/Compare/PWM

(CCP) Module” for more information.

Note 1: The ADIF bit is set at the completion of

every conversion, regardless of whether

or not the ADC interrupt is enabled.

2: The ADC operates during Sleep only

when the FRC oscillator is selected.

Note:

The GO/DONE bit should not be set in the

same instruction that turns on the ADC.

Refer to Section 9.2.6 “A/D Conversion

Procedure”.

Note:

A device Reset forces all registers to their

Reset state. Thus, the ADC module is

turned off and any pending conversion is

terminated.

PIC16F722-E/ML Datasheet(PDF) 102 Page - Microchip Technology

PIC16F722-E/ML Datasheet(HTML) 102 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL