PIC16F722-ESLASHML datasheet(152/302 Pages) MICROCHIP

152 / 302 page

PIC16F72X/PIC16LF72X

DS41341E-page 152

16.1.2.8

Asynchronous Reception Set-up:

Initialize the SPBRG register and the BRGH bit

to achieve the desired baud rate (refer to

Section 16.2 “AUSART Baud Rate Generator

(BRG)”).

Enable the serial port by setting the SPEN bit.

The SYNC bit must be clear for asynchronous

operation.

If interrupts are desired, set the RCIE bit of the

PIE1 register and the GIE and PEIE bits of the

INTCON register.

If 9-bit reception is desired, set the RX9 bit.

Enable reception by setting the CREN bit.

The RCIF interrupt flag bit of the PIR1 register

will be set when a character is transferred from

the RSR to the receive buffer. An interrupt will be

generated if the RCIE bit of the PIE1 register

was also set.

Read the RCSTA register to get the error flags

and, if 9-bit data reception is enabled, the ninth

data bit.

Get the received 8 Least Significant data bits

from the receive buffer by reading the RCREG

If an overrun occurred, clear the OERR flag by

clearing the CREN receiver enable bit.

16.1.2.9

9-bit Address Detection Mode Set-up

This mode would typically be used in RS-485 systems.

To set up an Asynchronous Reception with Address

Detect Enable:

Initialize the SPBRG register and the BRGH bit

to achieve the desired baud rate (refer to

Section 16.2 “AUSART Baud Rate Generator

(BRG)”).

Enable the serial port by setting the SPEN bit.

The SYNC bit must be clear for asynchronous

operation.

If interrupts are desired, set the RCIE bit of the

PIE1 register and the GIE and PEIE bits of the

INTCON register.

Enable 9-bit reception by setting the RX9 bit.

Enable address detection by setting the ADDEN

bit.

Enable reception by setting the CREN bit.

The RCIF interrupt flag bit of the PIR1 register

will be set when a character with the ninth bit set

is transferred from the RSR to the receive buffer.

An interrupt will be generated if the RCIE inter-

rupt enable bit of the PIE1 register was also set.

Read the RCSTA register to get the error flags.

The ninth data bit will always be set.

Get the received 8 Least Significant data bits

from the receive buffer by reading the RCREG

device’s address.

10. If an overrun occurred, clear the OERR flag by

clearing the CREN receiver enable bit.

11. If the device has been addressed, clear the

ADDEN bit to allow all received data into the

receive buffer and generate interrupts.

FIGURE 16-5:

ASYNCHRONOUS RECEPTION

Start

bit

bit 7/8

bit 1

bit 0

bit 7/8

bit 0

Stop

bit

Start

bit

Start

bit

bit 7/8

Stop

bit

RX/DT pin

Reg

Rcv Buffer Reg

Rcv Shift

Read Rcv

Buffer Reg

RCREG

RCIF

(Interrupt Flag)

OERR bit

CREN

Word 1

RCREG

Word 2

RCREG

Stop

bit

Note:

This timing diagram shows three words appearing on the RX input. The RCREG (receive buffer) is read after the third word,

causing the OERR (overrun) bit to be set.

PIC16F722-E/ML Datasheet(PDF) 152 Page - Microchip Technology

PIC16F722-E/ML Datasheet(HTML) 152 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL