| Electronic Components Datasheet Search |
|
MPC8358E Datasheet(PDF) 84 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
MPC8358E Datasheet(HTML) 84 Page - Freescale Semiconductor, Inc |
|
84 / 95 page ![]() MPC8358E PowerQUICC II Pro Processor Revision 2.1 PBGA Silicon Hardware Specifications, Rev. 3 84 Freescale Semiconductor Thermal • To configure the device with CSB clock rate of 266 MHz, core rate of 400 MHz, and QUICC Engine clock rate 300 MHz while the input clock rate is 33 MHz. Conf No. ‘s10’ and ‘c1’ are selected from Table 74. SPMF is 1000, CORPLL is 0000011, CEPMF is 01001, and CEPDF is 0. 23 Thermal This section describes the thermal specifications of the MPC8358E. 23.1 Thermal Characteristics Table 75 provides the package thermal characteristics for the 668 29 mm x 29 mm PBGA package. 23.2 Thermal Management Information For the following sections, PD = (VDD × IDD) + PI/O where PI/O is the power dissipation of the I/O drivers. See Table 5 for typical power dissipations values. Table 75. Package Thermal Characteristics for the PBGA Package Characteristic Symbol Value Unit Notes Junction-to-ambient Natural Convection on single layer board (1s) RθJA 20 °C/W 1, 2 Junction-to-ambient Natural Convection on four layer board (2s2p) RθJA 14 °C/W 1, 2, 3 Junction-to-ambient (@1 m/s) on single layer board (1s) RθJMA 15 °C/W 1, 3 Junction-to-ambient (@ 1 m/s) on four layer board (2s2p) RθJMA 11 •C/W C/W 1, 3 Junction-to-board thermal RθJB 6•C/W C/W 4 Junction-to-case thermal RθJC 4•C/W C/W 5 Junction-to-Package Natural Convection on Top ψJT 4•C/W C/W 6 Notes 1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. 2. Per JEDEC JESD51-2 and JEDEC JESD51-9 with the single layer board horizontal. 3. Per JEDEC JESD51-6 with the board horizontal. 1 m/sec is approximately equal to 200 linear feet per minute (LFM). 4. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on the top surface of the board near the package. 5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1). 6. Thermal characterization parameter indicating the temperature difference between package top and the junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |