PIC18F4550ESOSQTP datasheet(125/430 Pages) MICROCHIP

125 / 430 page

Preliminary

DS39632D-page 123

PIC18F2455/2550/4455/4550

10.5

PORTE, TRISE and LATE

Registers

Depending on the particular PIC18F2455/2550/4455/

4550 device selected, PORTE is implemented in two

different ways.

For 40/44-pin devices, PORTE is a 4-bit wide port.

Three pins (RE0/AN5/CK1SPP, RE1/AN6/CK2SPP

and RE2/AN7/OESPP) are individually configurable as

inputs or outputs. These pins have Schmitt Trigger

input buffers. When selected as an analog input, these

pins will read as ‘0’s.

The corresponding data direction register is TRISE.

Setting a TRISE bit (= 1) will make the corresponding

PORTE pin an input (i.e., put the corresponding output

driver in a high-impedance mode). Clearing a TRISE bit

(= 0) will make the corresponding PORTE pin an output

(i.e., put the contents of the output latch on the selected

pin).

addition

port

data,

the

PORTE

(Register 10-1) also contains the RDPU control bit

(PORTE<7>); this enables or disables the weak

pull-ups on PORTD.

TRISE controls the direction of the RE pins, even when

they are being used as analog inputs. The user must

make sure to keep the pins configured as inputs when

using them as analog inputs.

The Data Latch register (LATE) is also memory

mapped. Read-modify-write operations on the LATE

PORTE.

The fourth pin of PORTE (MCLR/VPP/RE3) is an input

only pin. Its operation is controlled by the MCLRE Config-

uration bit. When selected as a port pin (MCLRE = 0), it

functions as a digital input only pin; as such, it does not

have TRIS or LAT bits associated with its operation.

Otherwise, it functions as the device’s Master Clear input.

In either configuration, RE3 also functions as the

programming voltage input during programming.

EXAMPLE 10-5:

INITIALIZING PORTE

10.5.1

PORTE IN 28-PIN DEVICES

For 28-pin devices, PORTE is only available when Mas-

ter Clear functionality is disabled (MCLRE = 0). In these

cases, PORTE is a single bit, input only port comprised

of RE3 only. The pin operates as previously described.

Note:

On a Power-on Reset, RE2:RE0 are

configured as analog inputs.

Note:

On a Power-on Reset, RE3 is enabled as

a digital input only if Master Clear

functionality is disabled.

CLRF

PORTE

; Initialize PORTE by

; clearing output

; data latches

CLRF

LATE

; Alternate method

; to clear output

; data latches

MOVLW

0Ah

; Configure A/D

MOVWF

ADCON1

; for digital inputs

MOVLW

03h

; Value used to

; initialize data

; direction

MOVLW

07h

; Turn off

MOVWF

CMCON

; comparators

MOVWF

TRISC

; Set RE<0> as inputs

; RE<1> as outputs

; RE<2> as inputs

PORTE REGISTER

R/W-0

U-0

R/W-x

R/W-0

RDPU(3)

—

RE3(1,2)

RE2(3)

RE1(3)

RE0(3)

bit 7

bit 0

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

bit 7

RDPU: PORTD Pull-up Enable bit

= PORTD pull-ups are enabled by individual port latch values

= All PORTD pull-ups are disabled

bit 6-4

Unimplemented: Read as ‘0’

bit 3-0

RE3:RE0: PORTE Data Input bits(1,2,3)

Note 1:

implemented only when Master Clear functionality is disabled (MCLRE Configuration bit = 0); otherwise,

read as ‘0’.

RE3 is the only PORTE bit implemented on both 28-pin and 40/44-pin devices. All other bits are

implemented only when PORTE is implemented (i.e., 40/44-pin devices).

Unimplemented in 28-pin devices; read as ‘0’.

PIC18F4550ESOSQTP Datasheet(PDF) 125 Page - Microchip Technology

PIC18F4550ESOSQTP Datasheet(HTML) 125 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL