PIC17C752-08SLASHP datasheet(228/320 Pages) MICROCHIP

228 / 320 page

PIC17C75X

DS30264A-page 228

Preliminary

Output Low Voltage

D080

D081

VOL

I/O ports

with TTL buffer

–

0.1VDD

0.1VDD *

0.4

IOL = VDD/1.250 mA

4.5V

≤ VDD ≤ 6.0V

VDD

= 3.0V

IOL = 6 mA, VDD = 4.5V

Note 6

D082

RA2 and RA3

–

3.0

0.4

0.6

IOL = 60.0 mA, VDD = 6.0V

IOL = 60.0 mA, VDD = 2.5V

IOL = 60.0 mA, VDD = 4.5V

D083

D084

OSC2/CLKOUT

(RC and EC osc modes)

–

0.4

0.1VDD *

IOL = 1 mA, VDD = 4.5V

IOL = VDD/5 mA

(PIC17LC75X only)

Output High Voltage (Note 3)

D090

D091

VOH

I/O ports (except RA2 and RA3)

with TTL buffer

0.9VDD

0.9VDD *

2.4

–

IOH = -VDD/2.500 mA

4.5V

≤ VDD ≤ 6.0V

VDD

= 3.0V

IOH = -6.0 mA, VDD = 4.5V

Note 6

D093

D094

OSC2/CLKOUT

(RC and EC osc modes)

2.4

0.9VDD *

–

IOH = -5 mA, VDD = 4.5V

IOH = -VDD/5 mA

(PIC17LC75X only)

D150

VOD

Open Drain High Voltage

–

RA2 and RA3 pins only

Pulled-up to externally

applied voltage

Capacitive Loading Specs

on Output Pins

D100

COSC2 OSC2/CLKOUT pin

–

25 ‡

In EC or RC osc modes

when OSC2 pin is outputting

CLKOUT.

external clock is used to

drive OSC1.

D101

CIO

All I/O pins and OSC2

(in RC mode)

–

50 ‡

D102

CAD

System Interface Bus

(PORTC, PORTD and PORTE)

–

50 ‡

In Microprocessor or

Extended Microcontroller

mode

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40˚C

≤ TA ≤ +85˚C for industrial and

0˚C

≤ TA ≤ +70˚C for commercial

Operating voltage VDD range as described in Section 20.1

Param.

No.

Sym

Characteristic

Min

Typ†

Max Units

Conditions

These parameters are characterized but not tested.

†

Data in “Typ” column is at 5V, 25

°C unless otherwise stated. These parameters are for design guidance only

and are not tested.

‡

These parameters are for design guidance only and are not tested, nor characterized.

Note 1: In RC oscillator conﬁguration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the

PIC17CXXX devices be driven with external clock in RC mode.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The speciﬁed levels

represent normal operating conditions. Higher leakage current may be measured at different input voltages.

3: Negative current is deﬁned as coming out of the pin.

4: These speciﬁcations are for the programming of the on-chip program memory EPROM through the use of the

table write instructions. The complete programming speciﬁcations can be found in: PIC17C75X Programming

Speciﬁcations (Literature number DS TBD).

5: The MCLR/VPP pin may be kept in this range at times other than programming, but is not recommended.

6: For TTL buffers, the better of the two speciﬁcations may be used.

PIC17C752-08/P Datasheet(PDF) 228 Page - Microchip Technology

PIC17C752-08/P Datasheet(HTML) 228 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL