PIC18F6X2X datasheet(106/386 Pages) MICROCHIP

106 / 386 page

PIC18F6X2X/8X2X

DS39612A-page 104

Advance Information

 2003 Microchip Technology Inc.

9.6

INT0 Interrupt

External interrupts on the RB0/INT0, RB1/INT1,

RB2/INT2 and RB3/INT3 pins are edge-triggered:

either rising, if the corresponding INTEDGx bit is set in

the INTCON2 register or falling, if the INTEDGx bit is

clear. When a valid edge appears on the RBx/INTx pin,

the corresponding flag bit, INTxF, is set. This interrupt

can be disabled by clearing the corresponding enable

bit, INTxE. Flag bit, INTxF, must be cleared in software

in the Interrupt Service Routine before re-enabling the

interrupt. All external interrupts (INT0, INT1, INT2 and

INT3) can wake-up the processor from SLEEP if bit

INTxIE was set prior to going into SLEEP. If the global

interrupt enable bit GIE is set, the processor will branch

to the interrupt vector following wake-up.

The interrupt priority for INT1, INT2 and INT3 is

determined by the value contained in the interrupt

priority

bits:

INT1IP

(INTCON3<6>),

INT2IP

(INTCON3<7>) and INT3IP (INTCON2<1>). There is

no priority bit associated with INT0; it is always a high

priority interrupt source.

9.7

TMR0 Interrupt

In 8-bit mode (which is the default), an overflow in the

TMR0 register (FFh

→ 00h) will set flag bit TMR0IF. In

16-bit mode, an overflow in the TMR0H:TMR0L

registers (FFFFh

→ 0000h) will set flag bit TMR0IF. The

interrupt can be enabled/disabled by setting/clearing

enable bit, TMR0IE (INTCON<5>). Interrupt priority for

Timer0 is determined by the value contained in the

interrupt priority bit, TMR0IP (INTCON2<2>). See

Section 11.0 for further details on the Timer0 module.

9.8

PORTB Interrupt-on-Change

An input change on PORTB<7:4> sets flag bit RBIF

(INTCON<0>). The interrupt can be enabled/disabled

by setting/clearing enable bit, RBIE (INTCON<3>).

Interrupt priority for PORTB interrupt-on-change is

determined by the value contained in the interrupt

priority bit, RBIP (INTCON2<0>).

9.9

Context Saving During Interrupts

During an interrupt, the return PC value is saved on the

stack. Additionally, the WREG, STATUS and BSR

registers are saved on the fast return stack. If a fast

return from interrupt is not used (see Section 4.3), the

user may need to save the WREG, STATUS and BSR

registers

software.

Depending

the

user’s

application, other registers may also need to be saved.

Example 9-1 saves and restores the WREG, STATUS

and BSR registers during an Interrupt Service Routine.

EXAMPLE 9-1:

SAVING STATUS, WREG AND BSR REGISTERS IN RAM

MOVWF

W_TEMP

; W_TEMP is in virtual bank

MOVFF

STATUS, STATUS_TEMP

; STATUS_TEMP located anywhere

MOVFF

BSR,

BSR_TEMP

; BSR located anywhere

;

; USER ISR CODE

;

MOVFF

BSR_TEMP,

BSR

; Restore BSR

MOVF

W_TEMP,

; Restore WREG

MOVFF

STATUS_TEMP,STATUS

; Restore STATUS

PIC18F6X2X Datasheet(PDF) 106 Page - Microchip Technology

PIC18F6X2X Datasheet(HTML) 106 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL