| Electronic Components Datasheet Search |
|
TMS320VC5510 Datasheet(PDF) 20 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TMS320VC5510 Datasheet(HTML) 20 Page - Texas Instruments |
|
20 / 90 page ![]() Introduction 20 June 2000 − Revised September 2007 SPRS076O Table 2−2. Signal Descriptions (Continued) SIGNAL NAME DESCRIPTION OTHER‡ TYPE† JTAG EMULATION (CONTINUED) EMU0 I/O/Z A Emulation pin 0. When TRST is driven low, EMU0 must be high for activation of the OFF condition. When TRST is driven high, EMU0 is used as an interrupt to or from the emulator system and is defined as input/output by way of the IEEE standard 1449.1 scan system. EMU1/OFF I/O/Z A Emulation pin 1 / disable all outputs. When TRST is driven high, EMU1/OFF is used as an interrupt to or from the emulator system and is defined as input/output by way of the IEEE standard 1149.1 scan system. When TRST is driven low, EMU1/OFF is configured as OFF. The EMU1/OFF signal, when active low, puts all output drivers into the high-impedance state. Note that OFF is used exclusively for testing and emulation purposes (not for multiprocessing applications). Therefore, for the OFF feature, the following apply: TRST = low EMU0 = high EMU1/OFF = low RSVD[1:9] I/O Reserved. Reserved for future emulation purposes. These pins should be left unconnected. CLOCK SIGNALS CLKIN I C Clock input CLKOUT O/Z F Clock output. CLKOUT can represent the internal CPU clock or can be divided down to generate a slower clock by programming the CLKDIV field in the system register (SYSR). CLKMD I C Clock mode select. CLKMD selects the mode of the clock generator after reset. When CLKMD is low after reset, the clock generator will run at the same frequency as CLKIN. If CLKMD is high after reset, the clock generator will run at one-half of the frequency of CLKIN. The clock generator can later be reprogrammed in software. TIMERS TIN/TOUT0 I/O/Z F,H Timer 0 input/output. When configured as an output, TIN/TOUT0 generates a pulse or toggles when on-chip Timer 0 counts down to zero. When configured as an input, TIN/TOUT0 is used as a clock reference for Timer 0. The operation of this pin is configured in the timer control register (TCR0). TIN/TOUT1 I/O/Z F,H Timer 1 input/output. When configured as an output, TIN/TOUT1 generates a pulse or toggles when on-chip Timer 1 counts down to zero. When configured as an input, TIN/TOUT1 is used as a clock reference for Timer 1. The operation of this pin is configured in the timer control register (TCR1). GENERAL-PURPOSE I/O SIGNALS IO7 IO6 IO5 IO4 IO3/BOOTM2 IO2/BOOTM1 IO1/BOOTM0 IO0 I/O/Z F,G,H General-purpose configurable inputs/outputs. IO[7:0] can be individually configured as inputs or outputs via the GPIO direction register (IODIR). Data can be read from inputs or data written to outputs via the GPIO Data Register (IODATA). In addition, the bootloader uses IO4 as an output during the boot process. For detailed information on the operation of the bootloader, see the Using the TMS320VC5510 Bootloader application report (literature number SPRA763). Boot Mode Selection signals. BOOTM[2:0] are sampled following reset to configure the boot mode for the DSP. These signals are shared with IO[3:1]. After boot is complete, these signals can be used as general-purpose inputs/outputs. BOOTM3 I A Boot Mode Selection signal. BOOTM3 is sampled during the operation of the on-chip bootloader in conjunction with BOOTM[2:0] to configure the boot mode. XF O/Z F,H External flag output † I = Input, O = Output, S = Supply, Z = High impedance ‡ Other Pin Characteristics: A − Internal pullup (always enabled) E − Pin is high impedance in HOLD mode (due to HOLD pin). B − Internal pulldown (always enabled) F − Pin is high impedance in OFF mode (due to EMU1/OFF pin). C − Hysteresis input G − Pin can be configured as a general-purpose input. D − Pin has bus holder H − PIn can be configured as a general-purpose output. J − Internal pullup enabled by the HPE bit in the system register (SYSR) K − Internal pulldown enabled by the HPE bit in the system register (SYSR) |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |