F39-LSGA datasheet(86/109 Pages) OMRON

86 / 109 page

Common to F3SG-SR and F3SG-PG

Manual Reset Mode with EDM

[Wiring Example]

Note: For the functional earth connection, refer to page 83.

F3SG-SRA

Available

F3SG-PGA-A/-L

Available

F3SG-SRB

Available

F3SG-PGA-C

Available *6

KM1

KM2

F39-JGR3K-L

F39-JG

A-L

F39-JGR3K-D

F39-JG

A-D

Timing chart

24 VDC

Wiring for NPN

24 VDC

KM1

KM2

KM1

KM2

S1: Test switch

S2: Lockout/interlock reset switch

KM1, KM2: Safety relay with forcibly guided contacts (G7SA) or magnetic contactor

M: Motor

Beam state: Unblocked

Blocked

Test switch (S1)

Reset switch (S2)

OSSD

Needed

Intelligent Tap

*1. Reverse the polarity of the power supply when using in the NPN system.

*2. Connect the line to 0 VDC if Operating Range Selection is used in Short

Mode.

*3. This is the case for a PELV circuit.

*4. Set the function with the DIP Switches on the Intelligent Tap or the SD

Manager 3, restore the settings to the F3SG-SR/PG, and perform wiring

according to the wiring diagram.

*5. This wiring example shows light emission stop when connected to 24 VDC with

PNP setting, and light emission stop when connected to 0 VDC with NPN

setting. If TEST switch is not needed, refer to the User's Manual (Man. No.

Z405).

*6. When wiring the emitter/receiver of the F3SG-PGA-C, follow the same wiring

as for the receiver in the figure above. Wiring of the emitter side is not

required.

*7. The F3SG-PGA-C does not support the external test function.



: Indicates a switch position.

Function

Setting

DIP switch

SD Manager 3

EDM *4

EDM Enabled

[External device monitoring] : Enable

Interlock *4

Manual Reset (Start/

Restart Interlock)

[Start interlock] : Enable

[Restart interlock] : Enable

Operating Range Selection

Long : Open the OPERATING RANGE SELECT INPUT line of the emitter or connect the line to 24 VDC.

Non-Muting system

Perform wiring according to the wiring diagram.

N/A

[Muting]: Disable *4

External Test used *7

Connect the TEST line of the emitter to 24V/0V of the emitter via a test switch (NO contact).*5

N/A

[External test signal inversion] : Disable

Optical Synchronization

Do not connect the COM(+) and COM(-) lines of the of emitter and receiver with each other.

4ON

5ON

F39-LSGA Datasheet(PDF) 86 Page - Omron Electronics LLC

F39-LSGA Datasheet(HTML) 86 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL