F39-LSGA datasheet(92/109 Pages) OMRON

92 / 109 page

Common to F3SG-SR and F3SG-PG

Standard Muting Mode/Exit-Only Muting Mode with Intelligent Tap

[Wiring Example]

F3SG-SRA

Available

F3SG-PGA-A/-L

Available

F3SG-SRB

Available

F3SG-PGA-C

Available *11

F39-SGIT-IL3

24 VDC

Wiring for NPN

24 VDC

IO-Link

Master

F39-JG

B-L/

XS5F-D521-DJ0-IL

F39-JG

A-D

F39-JGR3K-L and F39-JG

□B-L

F39-JGR3K-D and

F39-JG

□B-D

PLC

IN1

Safety controller

*5 *6

IN2

MUTE A

MUTE B

OSSD

Timing chart

Beam state: Unblocked

Blocked

S1: Lockout reset switch, override switch or override cancel switch

S2, S3: Muting sensor

PLC: Programmable logic controller (Used for monitoring only. NOT related to safety system.)

Intelligent Tap

Needed



: Indicates a switch position.

Function

Setting

DIP switch

SD Manager 3

EDM *9

EDM Disabled

[External device monitoring] : Disable

Interlock *9

Auto Reset

[Start interlock] : Disable

[Restart interlock] : Disable

Operating Range Selection *10

Long

[Operating Range Selection] : Long mode

Standard Muting Mode

N/A

[Muting] : Enable

[Muting mode] : Standard Muting (Installation Example1/2)

Exit-Only Muting Mode

N/A

[Muting] : Enable

[Muting mode] : Exit-Only Muting

Test Input

N/A

Wired Synchronization

Connect the emitter and receiver with the Intelligent Tap.

3ON

4ON

5ON

8ON

*1. Reverse the polarity of the power supply when using in the NPN system. Select

a PLC and a safety controller of PNP or NPN type according to the system of

your application.

*2. Also used as OVERRIDE INPUT line.

*3. Make sure to connect an override cancel switch to the RESET line when using

the override function. Otherwise the override state may not be released by the

override cancel switch, resulting in serious injury.

*4. When connecting to the PLC, the output mode must be changed with the SD

Manager 3 according to your application. For the setting this function, refer to

the User's Manual (Man.No.Z405).

*5. Refer to page 79 for more information.

*6. The safety controller and the F3SG-SR/PG must share the power supply or be

connected to the common terminal of the power supply.

*7. For connecting with the IO-Link Master unit, refer to an instruction manual of the

IO-Link Master unit you use.

*8. This is the case for a PELV circuit.

*9. Set the function with the DIP Switches on the Intelligent Tap or SD Manager 3.

*10.Set the function with the DIP Switches on the Intelligent Tap or SD Manager 3

and wire according to the wiring diagram after restoring the settings to the

FE3SG-SR/PG when the F3SG-SR/PG or F3SG-PGA-L is used in Short Mode.

The F3SG-PGA-A/-C do not support the operating range selection function.

*11.When wiring the emitter/receiver of the F3SG-PGA-C, follow the same wiring

as for the receiver in the figure above. Wiring of the emitter side is not required.

Note: 1. When using the Intelligent Tap (F39-SGIT-IL3),

the following functions are not available.

• External Test

• Operating Range Selection by wiring

• Optical Synchronization

2. For the functional earth connection, refer to

page 83.

F39-LSGA Datasheet(PDF) 92 Page - Omron Electronics LLC

F39-LSGA Datasheet(HTML) 92 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL