F39-LSGA datasheet(88/109 Pages) OMRON

88 / 109 page

Common to F3SG-SR and F3SG-PG

Manual Reset Mode with Intelligent Tap

[Wiring Example]

Note: 1. When using the Intelligent Tap (F39-SGIT-IL3) with the emitter and receiver connected, the following functions are not available.

• External Test

• Operating Range Selection by wiring

• Optical Synchronization

2. For the functional earth connection, refer to page 83.

F3SG-SRA

Available

F3SG-PGA-A/-L

Available

F3SG-SRB

Available

F3SG-PGA-C

Available *9

F39-SGIT-IL3

24 VDC

IO-Link

Master

Wiring for NPN

24 VDC

F39-JG

B-L/

XS5F-D521-DJ0-IL

F39-JG

A-D

F39-JGR3K-L and

F39-JG

□B-L

F39-JGR3K-D and F39-JG

□B-D

PLC

IN1

IN2

S1: Lockout/interlock reset switch

PLC: Programmable logic controller (Used for monitoring only.

NOT related to safety system.)

Timing chart

Beam state: Unblocked

Blocked

Reset switch (S)

OSSD

Safety controller

*3 *4

Intelligent Tap

Needed

*1. Reverse the polarity of the power supply when using in the NPN system. Select a PLC

and a safety controller of PNP or NPN type according to the system of your application.

*2. When connecting to the PLC, the output mode must be changed with the SD

Manager 3 according to your application. For the setting this function, refer to the

User's Manual (Man.No.Z405).

*3. Refer to page 79 for more information.

*4. The safety controller and the F3SG-SR/PG must share the power supply or be

connected to the common terminal of the power supply.

*5. For connecting with the IO-Link Master unit, refer to an instruction manual of the IO-

Link Master unit you use.

*6. This is the case for a PELV circuit.

*7. Set the function with the DIP Switches on the Intelligent Tap or the SD Manager 3,

restore the settings to the F3SG-SR/PG, and perform wiring according to the wiring

diagram.

*8. To set the Short mode, set the function with the DIP Switches on the Intelligent Tap

or the SD Manager 3, restore the settings to the F3SG-SR/PG, and perform wiring

according to the wiring diagram.

*9. When wiring the emitter/receiver of the F3SG-PGA-C, follow the same wiring as for

the receiver in the figure above. Wiring of the emitter side is not required



: Indicates a switch position.

Function

Setting

DIP switch

SD Manager 3

EDM

EDM Disabled

[External device monitoring] : Disable

Interlock *7

Manual Reset (Start/

Restart Interlock)

[Start interlock] : Enable

[Restart interlock] : Enable

Operating Range Selection *8

Long

[Operating Range Selection] : Long mode

Non-Muting system

Perform wiring according to the wiring diagram.

N/A

[Muting] : Disable *7

Test Input

N/A

Wired Synchronization

Connect the emitter and receiver with the Intelligent Tap.

3ON

4ON

5ON

8ON

F39-LSGA Datasheet(PDF) 88 Page - Omron Electronics LLC

F39-LSGA Datasheet(HTML) 88 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL