LMH6583

SNOSAP5E – APRIL 2006 – REVISED MARCH 2013

www.ti.com

±3.3V Electrical Characteristics

(1) (continued)

Unless otherwise specified, typical conditions are: TA = 25°C, AV = +2, VS = ±3.3V, RL = 100Ω; Boldface limits apply at the

temperature extremes.

Symbol

Parameter

Conditions

Min (2)

Typ (3)

Max (2)

Units

VO

Output Voltage Range

RL = ∞

(7)

+2.1

±2.2

V

-2.05

PSRR

Power Supply Rejection Ratio

45

dB

ICC

Positive Supply Current

RL = ∞

98

120

mA

IEE

Negative Supply Current

RL = ∞

92

115

mA

Tri State Supply Current

RST Pin > 2.0V

17

25

mA

Miscellaneous Performance

RIN

Input Resistance

Non-Inverting

100

k

Ω

CIN

Input Capacitance

Non-Inverting

1

pF

RO

Output Resistance Enabled

Closed Loop, Enabled

300

m

Ω

RO

Output Resistance Disabled

Disabled

1100

1300

1450

Ω

CMVR

Input Common Mode Voltage Range

±1.3

V

IO

Output Current

Sourcing, VO = 0 V

±50

mA

Digital Control

VIH

Input Voltage High

2.0

V

VIL

Input Voltage Low

0.8

V

VOH

Output Voltage High

>2.2

V

VOL

Output Voltage Low

<0.4

V

TS

Setup Time

7

ns

TH

Hold Time

7

ns

(7)

This parameter is ensured by design and/or characterization and is not tested in production.

±5V Electrical Characteristics

(1)

Unless otherwise specified, typical conditions are: TA = 25°C, AV = +2, VS = ±5V, RL = 100Ω; Boldface limits apply at the

temperature extremes.

Symbol

Parameter

Conditions

Min (2)

Typ (3)

Max (2)

Units

Frequency Domain Performance

SSBW

−3 dB Bandwidth

VOUT = 0.5 VPP

475

LSBW

VOUT = 2 VPP, RL = 1 kΩ

550

MHz

VOUT = 2 VPP, RL = 150Ω

450

GF

0.1 dB Gain Flatness

VOUT = 2 VPP, RL = 150Ω

100

MHz

DG

Differential Gain

RL = 150Ω, 3.58 MHz/ 4.43 MHz

0.04

%

DP

Differential Phase

RL = 150Ω, 3.58 MHz/ 4.43 MHz

0.04

deg

Time Domain Response

tr

Rise Time

2V Step, 10% to 90%

1.4

ns

tf

Fall Time

2V Step, 10% to 90%

1.3

ns

OS

Overshoot

2V Step

2

%

SR

Slew Rate

6 VPP, 40% to 60%

(4)

1800

V/µs

ts

Settling Time

2V Step, VOUT Within 0.5%

7

ns

(1)

Electrical Table values apply only for factory testing conditions at the temperature indicated. No ensurance of parametric performance is

indicated in the electrical tables under conditions different than those tested.

(2)

Room Temperature limits are 100% production tested at 25°C. Device self heating results in TJ ≥ TA, however, test time is insufficient for

TJto reach steady state conditions. Limits over the operating temperature range are ensured through correlation using Statistical Quality

Control (SQC) methods.

(3)

Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

(4)

Slew Rate is the average of the rising and falling edges.

4

Submit Documentation Feedback

Copyright © 2006–2013, Texas Instruments Incorporated

Product Folder Links: LMH6583