 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
SPC563M60X Datasheet(PDF) 122 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
SPC563M60X Datasheet(HTML) 122 Page - STMicroelectronics |
|
|
122 / 128 page  Revision history SPC563M64x, SPC563M60x 122/128 DocID14642 Rev 12 15-Dec-2009 4 208-pin LBGA ballmap for the SPC563M60 (1024 KB Flash memory) has changed. Power Management Control (PMC) and Power On Reset (POR) electrical specifications updated Temperature sensor data added Specifications now indicate how each controller characteristic parameter is guaranteed. I/O pad current specifications updated I/O Pad VRC33 current specifications updated PAD AC characteristics updated VGA gain specifications added to eQADC electrical characteristics DC electrical specifications updated: – Footnote added to RPUPD100K and RPUPD200K: When the pull-up and pull-down of the same nominal 200 K or 100 K value are both enabled, assuming no interference from other devices, the resulting pad voltage will be 0.5 × VDDE ± 2.5% –IOL condition added to VOL_LS. –IOH condition added to VOH_LS. – Minimum VOH_LS is 2.3 V (was 2.7 V). – Separate IDDPLL removed from IDD spec because we can only measure IDD + IDDPLL. IDD increased by 15 mA (to 195 mA) to account for IDDPLL. IDD now documented as IDD + IDDPLL. Footnote added detailing runtime configuration used to measure IDD + IDDPLL. – Specifications for IDDSTBY and IDDSTBY150 reformatted to make more clear. –VSTBY is now specified by two ranges. The area in between those ranges is indeterminate. LVDS pad specifications updated: – Min value for VOD at SRC=0b01 is 90 mV (was 120); and 160 mV (was 180) at SRC = 0b10 Changes to Signal Properties table: – VDDE7 removed as voltage segment from Calibration bus pins. Calibration bus pins are powered by VDDE12 only. – GPIO[139] and GPIO[87] pins changed to Medium pads – Some signal names have changed on 176-pin QFP package pinout: “CAL_x” signals renamed to “ALT_x”. Changes to Pad Types table: – Column heading changed from “Voltage” to “Supply Voltage” – MultiV pad high swing mode voltage changed to 3.0 V – 5.25 V (was 4.5 V – 5.25 V) – MultiV pad low swing mode voltage changed to 4.5 V – 5.25 V (was 3.0 V – 3.6 V) Signal details table added Power/ground segmentation table added Table 45. Document revision history (continued) Date Revision Changes |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
New Zealand ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
