SPC563M60X datasheet(124/128 Pages) STMICROELECTRONICS

124 / 128 page

Revision history

SPC563M64x, SPC563M60x

124/128

DocID14642 Rev 12

15-Apr-2010

(cont.)

– (2) PMC 5 V supply voltage VDDREG min value is 4.5 V (was 4.75 V)

PMC electrical characteristics specifications updated

– (1d) Bandgap reference supply voltage variation is 3000 ppm/V (was 1500 ppm/V)

– (5a) Nominal 3.3 V supply internal regulator DC output voltage variation at power-on

reset min value is Vdd33-8.5% (was unspecified previously)

– (5a) Nominal 3.3 V supply internal regulator DC output voltage variation at power-on

reset max value is Vdd3+7% (was unspecified previously)

– (9a) Variation of POR for rising 5 V VDDREG supply max value is Por5V_r + 50%

(was Por5V_r + 35%)

– (9c) Variation of POR for falling 5 V VDDREG supply max value is Por5V_f + 50%

(was Por5V_f + 35%)

– (9c) note added: Minimum loading (<10 mA) for reading trim values from Flash,

powering internal RC oscillator, and IO consumption during POR.

“Core Voltage Regulator Controller External Components Preferred Configuration”

circuit diagram updated

Changes to DC Electrical Specifications:

– Footnote added to VDDE. VDDE must be less than VRC33 or there is additional leakage

on pins supplied by VDDE.

– Low range SRAM standby voltage (VSTBY) minimum changed to 0.95 V (was 0.9 V)

– Low range SRAM standby voltage (VSTBY) maximum changed to 1.2 V (was 1.3 V)

– High range SRAM standby voltage (VSTBY) minimum changed to 2.0 V (was 2.5 V)

–VIL_LS max value (Hysteresis disabled) changed to 0.9 V (was 1.1 V)

–VOH_LS min value changed to 2 V (was 2.3 V)

–IDDSLOW max value is 50 mA

–IDDSTOP max value is 50 mA

–IDDA max value is 30 mA (was 15.0 mA)

–IDD4 and VDDEH4 removed—they no longer exist

I/O pad average IDDE specifications table updated

I/O pad VRC33 average IDDE specifications table updated

LVDS pad specifications table updated

–VOS min value is 0.9 V (was 1.075 V)

–VOS max value is 1.6 V (was 1.325 V)

Updates to PLLMRFM electrical specifications:

– Maximum values for XTAL load capacitance added. The maximum value varies with

frequency.

– For a 20 MHz crystal the maximum load should be 17 pF.

Temperature sensor accuracy is ±10 °C (was ±5 °C)

Table 45. Document revision history (continued)

Date

Revision

Changes

SPC563M60X Datasheet(PDF) 124 Page - STMicroelectronics

SPC563M60X Datasheet(HTML) 124 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL